manualshive.com logo in svg

Landoll Brillion Turfmaker II, Руководство оператора

Поделиться
Скачать
Landoll Brillion Turfmaker II Скачать руководство пользователя страница 63

OPERATION

9K998-0522

3-5

Tractor Preparation/Attaching of 

Pull Type Seeder

DANGER

1. Align the Tractor Drawbar with the machine. Raise or 

lower the Drawbar, as needed, using the Jack. 
Attach the unit with proper size Hitch Pin and Safety 
Clip. 

2. Always move the Jack to the transport position 

before setting the machine in motion. 

3. Clean all Hydraulic Couplings and attach to the 

Tractor. 

4. Attach safety chain to tractor allowing plenty of 

movement for turning both directions. The safety 
chain should latch securely to prevent it from coming 
loose. 

See Figure 3-5.

IMPORTANT

If the Clevis Pin is not installed, the Transport Lock 
may bounce up and cause significant damage to the 
Cylinder and Hydraulic Fittings.

Figure 3-5:  Safety Chain

5. If Transport Locks are not engaged, fully extend the 

Hydraulic Lift Cylinders and rotate Transport Locks in 
the engaged position over the Cylinder Rods. Secure 
with the Clevis Pins and Hairpin Cotters. 

See 

Figure 3-6.

Figure 3-6:  Transport Lock Engaged

6. Connect the 7-Pin Connector to Tractor Outlet, 

routing cable by avoiding pinch points.

  • Make sure the Tractor has a good clean 

Receptacle, free of dirt and corrosion.

  • Make sure the 7-Pin Connector is inserted ALL the 

way in. With tighter fitting pins, operator may think 
the Connector is all the way in, but really isn’t.

  • Make sure the Tractor Receptacle Cover latches 

over the keyway on the 7-Pin Connector to hold 
the Connector in place.

  • If an operator plugs in the 7-Pin Connector, but the 

lights do not seem to work right, check the above 
items to make sure there is a good connection with 
the 7-Pin Connector.

7. Install Clutch Switch Box or Brillion Elite Mini Monitor 

to tractor. 

Clutch Switch Box:

 Connect Clutch Switch Box 

Cord with Ring Terminals to tractor power source. 
Ring Terminals can be removed and replaced with a 
different power source connector. Connect 2-Pin 
Connector to Clutch Harness.

Brillion Elite Mini Monitor:

 Connect the Elite Mini 

Tractor Harness to 14-Pin Connector to Brillion Mini 
Monitor, 3-Pin Plug to the 12 Volt Tractor 
Convenience Outlet and 6-Pin Connector to 240" 
Extension Harness. Elite Mini Tractor Harness 4-Pin 
Connector is not used this time. 

Do not allow any bystanders to stand between 
the tractor and the implement while backing up to 
the implement.

Drawbar 
Support

Locknut, 3/4-10

 Bolt,  

3/4-10 x 2-1/4

9" Max.

Tractor Drawbar

Safety Chain

Flat 

Washer, 3/4"

Safety Chain 

Intermediate

     Support 

Wheel Arm 

Transport Lock

Clevis Pin

Hair Pin

Cotter

Frame

Engaged

Cylinder

Содержание Brillion Turfmaker II













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды