manualshive.com logo in svg

Landoll Brillion Turfmaker II, Руководство оператора

Поделиться
Скачать
Landoll Brillion Turfmaker II Скачать руководство пользователя страница 69

OPERATION

9K998-0522

3-11

Figure 3-14:  Seed Chart, Rear Box

NOTES

Brillion assumes no liability pertaining to seeding rates achieved with this seeder. Rates listed are general in nature and should be used as starting 
points only. Seed varieties and blends listed represent those calibrated through in-house test meters. Variations in actual rates may be realized due 
to differences in seed lots. For accurate rates with seeds being used, follow the calibration instructions listed on the seed chart inside the box cover 
or refer to the Operator’s Manual.

 The information listed in the above seed charts is subject to change without notice.

*

*

1.  RA

TES 

ARE FOR 1

1

 T

OOTH DRIVER.  DOUBLE 

THESE V

ALUES FOR 22 

T

OOTH DRIVER.

2.  RA

TES 

ARE INTENDED 

AS 

A

 GUIDE ONL

Y

.  V

ARIA

TIONS IN SIZE 

AND CLEANLINESS WILL

 AFFECT

 RA

TES.

     CHECK 

ACREAGE 

AND POUNDS OF SEED USED FOR BEST

 RESUL

TS.

PLANTING RA

TES FOR REAR SEED BOX

Содержание Brillion Turfmaker II













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды