Landoll BRILLION TURFMAKER II SL Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 100

background image

3-2

9K998

OPERATION

Seeder Operation

This chapter covers the basic operation and usage
procedures for the Landoll Brillion Turfmaker Seeder. Be
sure to read and understand the Safety Procedures and
Cautions starting on

Tractor Preparation

The Turfmaker Seeder is available as a Pull Type or 3Pt
mounted version.
A Pull Type Seeder is equipped to be pulled by a Tractor
with a drawbar, no clevis.
A 3Pt mounted Seeder is compatible with CAT 2 Free
Link, CAT 2 Quick Coupler and CAT 3 Narrow Quick
Coupler.

Tractor Preparation/Attaching of

3Pt Hitch Seeders

1. Brillion 8, 10, and 12 Foot 3Pt Seeders are designed

to be pulled with Category 2 Free Link and Category
2 or 3N Quick Hitch Coupler 3Pt Hitches.

Figure 3-1.

Be sure Tractor's Hitch Capacity is not

exceeded by the Laden Mass of the Seeder.

Refer

to Tractor Operator's Manual.

2. Be sure Tractor is properly ballasted. A minimum

25% of Tractor and Equipment Laden Mass must be
on Tractor Front Wheels in transport position to
maintain stability. Calculate the Loaded Seeder
Mass.

(See “Reference Tables and

Specifications” on page 5-1.)

. (Seeder weight plus

the seed box capacity with desired seed.)

Refer to

Tractor Operator's Manual.

3. Check the Tractor tire inflation levels to ensure that

they are properly inflated for the additional Laden
Seeder Mass. Refer to the Tractor Operator's
Manual. Be sure not to over ballast and exceed
Tractor Tire Capacity.

4. Set Tractor 3Pt Lower Links to allow lateral

(torsional) float.

Refer to Tractor Operator's

Manual.

If left rigid, your Brillion Seeder may not

follow ground contours resulting in a poor
germination.

5. Set Lift Rod length long enough to ensure Seeder

can float downward in the case of a furrow or
waterway. Lower Links should be the same height,
leveling your Brillion Seeder side to side. Fine
adjustments may need to be made after hookup is
completed.

Refer to the Tractor Operator's

Manual.

6. Attach Seeder to the Tractor's 3Pt Free Link or Quick

Hitch Coupler using the appropriate size pins and
bushings. Be sure to use the hardware provided and
is in good working order.

See Figure 3-1.

7. Refer to the Tractor Operator's Manual for Quick

Hitch Operation.



DANGER

8. Plug 7 Pin connector to Tractor Outlet, routing cable

by avoiding pinch points.

• Make sure the Tractor has a good clean Receptacle,

free of dirt and corrosion.

• Make sure the 7 Pin Connector is inserted ALL the

way in. With tighter fitting pins, operator may think
the Connector is all the way in, but really isn’t.

• Make sure the Tractor Receptacle Cover latches

over the keyway on the 7 Pin Connector to hold the
Connector in place.

• If an operator plugs in the 7 Pin Connector, but the

lights do not seem to work right, check the above
items to make sure there is a good connection with
the 7 Pin Connector.

9. Install Clutch Switch and Harness to Tractor.

See

“Electric Clutch Kit” on page 2-18.

10. Raise seeder. Remove Parking Pin.

See Figures 3-2

. Adjust or lock tractor sway stabilizers if

equipped, centering the Seeder with the Tractor.

Refer to the Tractor Operator's Manual.

11. Lower Seeder, if necessary level Seeder side to side

(laterally) by adjusting Lift Rod length. Level Seeder
front to back by adjusting the Tractor Upper Link
length as required.

Refer to the Tractor Operator’s

Manual.

Do not allow any bystanders to stand between
the tractor and the implement while backing up to
the implement.

«
...
58
59
60
61
62
...
»

Содержание BRILLION TURFMAKER II SL





































































































Отзывы:

Нет отзывов

Похожие инструкции для BRILLION TURFMAKER II SL

Бренд: Backyard Play Systems Страницы: 54

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: Teac Страницы: 76

Бренд: Teac Страницы: 3

Бренд: Teac Страницы: 50

Бренд: Teagle Страницы: 2

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 24

Бренд: RAMVAC Страницы: 53

Бренд: Unitech Страницы: 37

Бренд: Neilsen Страницы: 8

Бренд: EZ Digital Страницы: 53

Бренд: Dentsply Sirona Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды