Landoll Brillion Turfmaker II Series Скачать руководство пользователя страница 32

Страница: 32 / 114

2-14

9K998-2306

TABLE OF CONTENTS

Latch Installation

Large Seed Box Cover with Latches and Gas Springs
1. Place the gasket on latch base and place on Seed

Box Cover.

2. Install slotted screws to secure Latch to Cover.
3. Thread the nut onto latch rod, then slide on Internal

Tooth Washer, Pawl, the other Internal Tooth Washer
and then thread on the other nut. Hand tighten only.

Close the Cover and turn Latch to see if Pawl fits snug up
against seed box lip. If it does not, open Cover and adjust
nuts accordingly. When properly adjusted, securely
tighten latch nuts.

Cover Gas Spring Installation

NOTE

Gas Spring rod end must be down for proper
functionality.
1. Snap Gas Spring rod end onto Seed Box Gas Spring

Bracket.

2. Swing Gas Spring base end up to Cover Ball Stud and

snap in place.

Figure 2-20: Latch Installation

Latch

Gasket

(2) Slotted

Screws

Pawl

(2) Nut

(2) Internal

Tooth

Washers

Pawl

(Closed Position)

Gas Spring

Rod end must

be down

Gas Spring

Mounting Bracket

Ball Stud

Locknut,5/16-18

Gas Spring

Cover

Latch

Latch Pawl

Slotted Screws

Bolt,1/4-20

x 1/2

Содержание Brillion Turfmaker II Series



















































































































Результаты поиска

Содержание Brillion Turfmaker II Series

Отзывы:

Похожие инструкции для Brillion Turfmaker II Series

Бренды по названию

Популярные бренды

Landoll Brillion Turfmaker II Series, Руководство оператора

Результаты поиска

Содержание Brillion Turfmaker II Series

Отзывы:

Похожие инструкции для Brillion Turfmaker II Series

Бренды по названию

Популярные бренды