background image

     

The instructions stated on the LP cylin-

ders have to be followed whe filling and 

transporting cylinders.  Failure to do so 

could result in problems relating to overfill-

ing, excessive venting of gas and to regula-

tor freezing.

(A) DO NOT store tanks under or near 

the smoker.

(B) NEVER fill cylinders more than 80% 

full.

If instructions A and B above are not 

followed exactly, a fire causing death

or serious injury may occur.

Do not allow dirt or foreign material to get into or 

onto the cylinder connection when it is not 

attached to the fuel supply system.  Place the 

dust cap on the cylinder valve outlet whenever 

the cylinder is not in use.  Only install the type of 

dusct cap on the cylinder valuve outlet that is 

provided with the cylinder valve.  Other types of 

caps or plugs may result in leakage of propane.

20

WARNING

CONNECTING THE LP CYLINDER

ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE 

FOLLOWED TO PREVENT FIRE, DAMAGE AND/OR INJURY.

This smoker is designed to operate on LP (Liquified 

Propane) gas only.  This smoker is not to be 

utilized with non-self-contained LP gas supply 

system.
The 20 lb LP Cylinder used with this smoker must 

conform  to the following requirements:

     Diameter - 12” (30.5cm)

     Height - 18” (45.7cm)

     With a maximum capacity of 20 pounds.

The LP cylinder used must include a color to 

protect the cylinder valve. The cylinder system 

must be arranged for vapor withdrawal.

IMPORTANT:

 

 

Any fuel supply cylinder 

used must be constructed and marked in 

accordance with specifications for propane 

cylinders of the U.S. Department of 

Transportation (DOT) CFR 49, or CAN/CSA 

B339.  The appliance used only with the 20 

pound, vertical standing vapor 

withdrawal type tank.

Gas Cylinder outlet must have Type 1 gas 

connection termination in order to mate with 

gas hose provided with smoker.

The pressure regulator and hose assembly 

supplied by the manufacturer with the smoker 

must be used.  Replacement pressure regula-

tors and hose assemblies must be those speci-

fied by the smoker manufacturer.

The regulator/hose assembly should be 

handled carefully to prevent contamination by 

foreign objects and dirt.  The assembly should 

be inspected before use and any dirt or con-

tamination should be wiped off.  In order to 

insure proper installation, any replacement of 

the fuel cylinder regulator assembly has to 

done with parts authorized by the smoker 

manufacturer.

If there is a question on the identity of 

your smoker and of the type of fuel to be 

used, please look on the data plate.  

Smokers are factory equipped for use on 

only one type of fuel.  These smokers 

cannot be, and should not be used on 

other types of fuel.  Doing so can cause 

severe damage to the smoker and the 

installation area and the added risk of 

serious injury.

Any attempt to operate these smokers on 

fuels for which they are not design certi-

fied VOIDS THE MANUFACTURER’S 

WARRANTY.

Cylinders must be filled before initial use.  All 

handling, transport, filling and storage of LP 

gas cylinders must be in accordance with NFPA 

58 Storage and Handling of Liquid Petroleum 

Gases, or CSAB 149.1 Natural Gas and Propane 

Installation code.  Clylinders must be suitably 

tied down during transport.  DO NOT place any 

other items on top of the cylinders at any time.  

Cylinders are not to be exposed to excessive 

temperatures or high heat.

DANGER

Содержание 3875GWLACR






























Отзывы: