14
Operations
Warnings & Check List
1. Installation or servicing of gas
appliances and controls must
only be performed by qualified
personnel. After installation or
servicing, test manual valve,
operating valves, pressure regu
-
lation, and automatic shut-off
valve for proper operation.
2. Install in a suitable dry location.
The machine must be located in
an area properly protected from the weather.
3. Shut off gas and electricity before starting installa
-
tion or service. Turn back on to test or operate.
4.
DO NOT
connect appliances before pressure
testing the gas piping. Damage to gas valve may
result. (6 - 14 w.c.i. or 1/2 psig)
5.
DO NOT
insert any object other than suitable pipe
or tubing in the inlet or outlet of the gas valve.
Internal damage may occur and result in a
hazardous condition.
6.
DO NOT
grip gas valve body with a pipe wrench or
vise. Damage may result causing gas leakage.
Use inlet or outlet bosses or a special body
wrench.
7.
DO NOT
short the gas valve terminals.
8.
DO NOT
allow any flame to impinge on the
regulator vent tubing if supplied. It may clog and
cause gas valve malfunction.
9.
DO NOT
use the gas cock to adjust gas flow.
10. If main burner fails to shut off, turn off
gas supply.
11. Keep all combustible materials away from gas
appliances.
DO NOT
allow lint or dust to collect in
burner area.
12. Dials must only be operated by hand. Never use
pliers, wrenches or other tools to turn dials.
13. After installation or servicing, test for leaks with a
soap solution. With the main burner on, coat pipe
and tubing joints, gaskets, etc. Bubbles indicate
leaks.
14. If the machine is installed in an enclosed room,
care should be taken to ensure that an adequate
supply of air is available for combustion and venti
-
lation. (1 sq. inch per 1000 BTU)
FOR YOUR SAFETY READ BEFORE
LIGHTING
If you do not follow these instructions exactly, a fire
or explosion may result causing property damage,
personal injury or loss of life.
A. This appliance has a pilot which must be lighted
by hand. When lighting the pilot, follow these
instructions exactly.
B. Before lighting, smell all around the appliance
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle
on the floor.
FOR YOUR SAFETY
“WHAT TO DO IF YOU SMELL GAS”
•
• Do not try to light any appliance
•
• Do not touch any electrical switch, do not
use any phone in your building.
•
• Immediately call your gas supplier from a
neighbor’s phone.Follow the gas supplier’s
instructions.
•
• If you cannot reach your gas supplier, call
the fire department.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, don’t try to repair it; call a
qualified service technician. Forced or attempted
repair may result in a fire or explosion.
D. Do not use this appliance if any part has been
under water. Immediately call a qualified service
technician to inspect the appliance and to replace
any part of the control system and any gas control
which has been under water.
Landa NG 3000 Operator’s Manual 8.913-942.0 - E
WARNING
READ OPERATOR’S
MANUAL THOROUGHLY
PRIOR TO USE.
OPERATIONS
SAFET
Y
MAINTENANCE
Содержание NG-3000
