manualshive.com logo in svg
background image

8.917-208.0  •  HOT Operator Manual •  Rev. 03/12

15

 

 

PRESSURE W

ASHER

 

OPERA

T

OR’S MAN 

AL

  

PREVENTATIVE MAINTENANCE

OIL CHANGE RECORD

This pressure washer was produced with the best avail able ma te ri als and quality craftsmanship. However, you 
as the own er have certain re spon si bil i ties for the correct care of the equip ment. At ten tion to reg u lar pre ven ta tive 
main te nance pro ce dures will as sist in preserving the performance of your equipment. Contact your LANDA dealer 
for main te nance. Regular preventative maintenance will add many hours to the life of your pressure wash er. 
Perform maintenance more often under severe conditions.

Date Oil Changed 

Month/Day/Year

Estimated Operating 

Hours Since Last 

Oil Change

Date Oil Changed 

Month/Day/Year

Estimated Operating 

Hours Since Last 

Oil Change

MAINTENANCE SCHEDULE

Pump Oil

Inspect

Daily inspect the oil level

Change

After fi rst 50 hours, then every 500 hours or annually

Clean Burner Filter

Annually

Remove Burner Soot From Heating Coil

Annually

Check Belt Tension

Monthly

Descale Coil

Annually - (more often if required)

Replace High Pressure Nozzle

Every 6 months

Replace Quick Connects

Annually

Clean Water and Detergent Screen/Filter Weekly

Replace HP Hose

If there is any sign of wear

Grease Motor

Every 10,000 hours

Check Burner Nozzles

Annually

Unloader Valve

Annually

Содержание HOT 3-300




















Отзывы: