manualshive.com logo in svg
background image

12

Operations

Insulated Straight Wand 
Assembly

Attach the pressure hose to the 
spray gun using teflon tape on hose 
threads. Attach nozzle, extension 
to spray gun/wand. Tighten both by 
hand.

Before installing nozzle, turn on 
water supply and run machine 
allowing water to flush through the 
system until clear.

Pull spring-loaded collar of the 
wand coupler back to insert your 
choice of pressure nozzle or soap 
nozzle. Release the coupler collar 
and push the nozzle until the collar 
clicks. Pull the nozzle to make sure 
it is seated properly. 

NOTE: High pressure nozzle must be inserted at end 
of wand to obtain high pressure.

Variable Pressure Wand Assembly

 Models using variable pressure wands, grip spray gun 
securely. Turn variable pressure control handle counter-
clockwise to reduce pressure and for applying soap 
through the brass soap nozzle with detergent injector 
attached.

Steam Wand Assembly

This wand assembly is only used on midel HOT 3-
30036D for steam. No high pressure or soap nozzle can 
be used.

Variable Pressure 

Control Handle

Trigger

Variable Pressure 

Wand (VP)

High 

Pressure 

Nozzle

Brass Soap Nozzle

Steam 

Hose

Steam Nozzle

Steam Wand

(3-300)

Landa HOT Series Operator’s Manual  8.917-208.0 - B

Nozzle Extension

Spray  

Gun/Wand

Wand 

Coupler

Pressure or Soap

Nozzle

Pressure or Soap 

Nozzle

Wand 

Coupler

Coupler

Collar

Содержание 1.109-093.0























Отзывы: