background image

Section 5:  Maintenance & Lubrication 

Table of Contents

1/25/21

STB0554 & STB0560 Snow Trip Blade 301-701M

24

Poly Cutting Edge Removal and Assembly

Refer to Figure 5-2:

1. Remove all but the two outside carriage bolts (#2) 

and nuts (#3) from moldboard (#5).

2. Loosen the two outside nuts (#3). Do not remove 

nuts at this time.

3. Hold one end of blade (#4) and retaining plate (#1) 

up and remove carriage bolt (#2) and nut (#3) from 

that end. Lower that end down to the ground.

4. Hold opposite end of blade (#4) and retaining 

plate (#1) up and remove carriage bolt (#2) from that 

end. Lower blade (#4) and retaining plate (#1) to the 

ground.

5. Inspect carriage bolts (#2) and nuts (#3) for wear. 

Replace as needed. 

6. Inspect blade (#4). Rotate or replace blade (#4) if 

excessively worn.

7. With blade (#4) down, raise one end up and attach to 

moldboard (#5) with carriage bolt (#2), retaining

plate (#1), and nut (#3). Draw nut (#3) up snug but do 

not tighten.

8. Raise the other side of blade (#4) and retaining 

plate (#1) up and attach to moldboard (#5) with 

carriage bolt (#2), retaining plate (#1), and nut (#3). 

Draw nut (#3) up snug but do not tighten.

NOTE:  

Cutting edge is removable and reversible.

9. Install remaining 5/8"-11 x 1 1/2" GR5 carriage

bolts (#2) and nuts (#3). Tighten all nuts to the correct 

torque.

10. Return to the tractor. Raise unit up and remove 

support blocks.

Poly Cutting Edge Removal and Assembly

Figure 5-2

74857

5

3

1

2

4

Содержание STB0554





































Отзывы: