background image

Section 1:  Assembly & Set-up 

Table of Contents

1/25/21

STB0554 & STB0560 Snow Trip Blade 301-701M

10

Tractor Requirements

The Snow Trip Blade is designed to attach to tractor 

loaders equipped with a universal quick-attach hitch with 

the following requirements:
Horsepower Requirements  . . 17-30 hp (12.7 - 22.4 kW)
Tractor Weight. . . . . . . . .  Less than 2,000 lbs (900 kg)
Tractor Hitch . . . . . . . . . . . . . . . . . . . . . . . .  ISO 24410
Max SAE Lift Capacity. . .  Less than 1,000 lbs (450 kg)
Max Hydraulic Pressure Rating . . . . 3,000 psi (21 mPa)
Hydraulic Connections. . . . . . . . . . 2 - Hydraulic Outlets

Before You Start

Make sure the intended tractor conforms to the 

requirements stated above. Also, read and understand 

this Operator’s Manual for your Snow Trip Blade. An 

understanding of how it works will aid in its assembly and 

set-up. 
Go through the 

Pre-Assembly Checklist

 before 

assembling the Snow Trip Blade. To speed up your 

assembly task and make the job safer, have all needed 

parts and equipment readily at hand.

Pre-Assembly Checklist

Check

Reference

Have a hoist, fork lift or loader with properly sized chains and 
safety stands capable of lifting and supporting the equipment 
on hand.
Have a minimum of two people available during assembly.
Make sure all major components and loose 
parts are shipped with the machine.

Assembly 

& Set-up

Double check to make sure all parts, fasteners, 
and pins are installed in the correct location. 
Refer to the Parts Manual if unsure. By double 
checking, you will lessen the chance of 
incorrectly using a bolt that may be needed 
later.

NOTE:

 All assembled hardware from the 

factory has been installed in the correct 
location. Remember location of a part or 
fastener if removed. Keep parts separated.

Operator’s 

Manual 

301-701M

Parts Manual 

301-701P

Make sure working parts move freely, bolts are 
tight & cotter pins are spread.

Operator’s

Manual

Make sure all grease fittings are in place and 
lubricated.

Page 26

Make sure all safety labels are correctly 
located and legible. Replace if damaged.

Page 6

Make sure all red and amber reflectors are 
correctly located and visible when machine is 
in transport position.

Page 8

NOTE:  

Hydraulic connections are only required if 

the Snow Trip Blade is equipped with hydraulic 

angling option.

IMPORTANT: 

Ballast may need to be added to your 

tractor to maintain steering control and to prevent 

tipping. Refer to your tractor’s operator manual to 

determine if additional ballast is needed.

Torque Requirements

Refer to 

“Torque Values Chart for Common Bolt Sizes” 

on page 30 to determine correct torque values when 

tightening hardware.

Tractor Shutdown Procedure

The following are basic tractor shutdown procedures. 

Follow these procedures and any additional shutdown 

procedures provided in your tractor Operator’s Manual 

before leaving the operator’s seat.
1. Reduce engine speed and shut-off all power to the 

attachment. 

2. Park tractor and attachment on solid, level ground.
3. Lower attachment until it is flat on the ground or on 

non-concrete support blocks. 

4. Put tractor in park or set park brake, turn off engine, 

and remove ignition key to prevent unauthorized 

starting.

5. Relieve all hydraulic pressure to auxiliary hydraulic 

lines.

6. Wait for all components to come to a complete stop 

before leaving the operator’s seat.

7.

Use steps, grab-handles and anti-slip surfaces when 

stepping on and off the tractor.

Cutting Edge Assembly

Land Pride offers two cutting edge options, steel cutting 

edge and poly cutting edge, for the Snow Trip Blade. The 

steel cutting edge for tougher applications and the poly 

cutting edge for applications where you want to be more 

gentle on the surface being bladed such as asphalt 

parking lots.

Steel Cutting Edge Assembly

Refer to 

Figure 1-1

 on page 11:

1. Locate steel cutting edge (#2) two plow bolts (#1) 

and two hex flange locknuts (#4). 

2. Insert plow bolt (#1) through the cutting edge (#2) 

and moldboard (#3) on one end first and hand tighten 

hex flange locknut (#4).

3. Repeat step 2 for the opposite end.
4. Install remaining bolts (#1) and hex flange 

locknuts (#4). 

5. Tighten nuts to proper torque.
6. Lower the Snow Trip Blade to level ground.

Poly Cutting Edge Assembly

Refer to 

Figure 1-2

 on page 11:

1. Locate the poly cutting edge (#4) two carriage 

bolts (#2), retaining plate (#1) and two hex flange 

locknuts (#3).

2. Insert carriage bolt (#2) through the retaining 

plate (#1), the cutting edge (#4) and moldboard (#5) 

on one end first. Attach hex flange locknut (#3) and 

hand tighten.

Section 1:  Assembly & Set-up

Содержание STB0554





































Отзывы: