Land Pride RCFM4014, Руководство оператора

Страница: 32 / 52

Section 4: Operating Instructions
Table of Contents
RCFM4014 Rotary Cutter 326-730M 8/11/14
28
Section 4: Operating Instructions
Operating Checklist
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the Rotary Cutter. It is absolutely
essential that no one operates the cutter unless they are
age 16 or older and have read, fully understood, and are
totally familiar with the Operator’s Manual. Make sure the
operator has paid particular attention to:
•
Important Safety Information , pages 1
•
Section 1: Assembly & Set-Up, page 12
•
Section 3: Adjustments , page 25
•
Section 4: Operating Instructions , page 28
•
Section 5: Maintenance & Lubrication , page 33
Perform the following inspections before using your
Rotary Cutter.
Safety Information
DANGER
!
To avoid serious injury or death:
•
Do not engage power take-off while hooking-up or
unhooking the driveline, or while someone is standing near
the driveline. A person’s body and/or clothing can become
entangled in the driveline.
•
Always disconnect driveline from the tractor and secure
implement in the up position with solid, non-concrete
supports before servicing the underside. A person can
become entangled in the drivetrain if the tractor is started
and power take-off is engaged or crushed by an
unsupported implement.
Operating Checklist

Check Page
Read and follow all safety information carefully.
Refer to “Important Safety Information”.
1
Make sure all guards and shields are in place.
Refer to “Important Safety Information”.
1
Make sure there are no hydraulic leaks.
Refer to “Avoid High Pressure Fluids Hazard”.
3
Read and follow hook-up & preparation.
Refer to “Section 1: Assembly & Set-Up”.
12
Read and make all required adjustments.
Refer to “Section 3: Adjustments”.
25
Read and follow all operating procedures.
Refer to “Section 4: Operating Instructions”.
28
Read and follow all maintenance instructions.
Refer to “Section 5: Maintenance & Lubrication”.
33
Read and follow all lubrication Instructions.
Refer to “Lubrication Points”.
47
Check cutter initially and periodically for loose
bolts and pins. Refer to “Torque Values Chart”.
46
Make sure all gearboxes are properly lubricated.
Refer to Gearbox lubrication.
47
•
Tractor power take-off shaft shield, driveline shields, and
gearbox shaft shields must be installed and in good working
condition to avoid driveline entanglement and projectiles
flying off of the driveline.
•
All guards and shields must be installed and in good
working condition while operating the implement.
•
Never place hands or feet under the deck or attempt to make
adjustments to the cutter with power take-off engaged.
Cutter blades rotating at high speeds cannot be seen and are
located close to the deck sides. Body extremities will be cut
off instantly.
• Rotary Cutters have the ability to discharge objects at high
speeds; therefore, the use of front and rear safety guards is
mandatory when cutting along roadways and in areas where
people may be present. Stop blade rotation if a bystander is
in or around the area.
•
Do not use cutter as a fan. Cutting blades are not properly
designed or guarded for this use.
•
Always disengage power take-off before lifting implement
up, and never operate implement in the raised position.
Objects can be thrown at high speeds toward people or
animals
•
Make certain driveline yokes are securely fastened at each
end. A loose yoke can work free allowing the driveline to
rotate uncontrollably causing implement damage and
bodily injury or death to anyone nearby.
WARNING
!
To avoid serious injury or death:
•
Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting implement
back into service. Serious breakdowns can result in injury
or death.
• Never carry riders on the implement or power machine.
Riders can obstruct the operator’s view, interfere with
control of the equipment, be pinched by moving
components, become entangled in rotating components, be
struck by objects, be thrown or fall from the equipment, etc.
•
Always shut tractor down using “Tractor Shutdown
Procedure” provided in this manual before dismounting
tractor.
• Do not operate and/or travel across inclines where tractor
and/or implement can roll over. Consult your tractor’s
manual for acceptable inclines the tractor is capable of
traveling across.
• A rotating driveline must not exceed an angle of 25 degrees
up or down, and never engage a driveline while at an angle
exceeding 25 degrees up or down. The driveline can break
and send projectiles.
• Do not use implement to lift objects; to pull objects such as
fence posts, stumps, etc; or to push objects. The unit is not
designed or guarded for these uses.
•
Do not use implement as a man lift or work platform. It is
not properly designed or guarded for this use.