Land Pride RCFM4014 Скачать руководство пользователя

Страница: 33 / 52

Section 4: Operating Instructions

Table of Contents

RCFM4014 Rotary Cutter 326-730M

12/11/18

•

Do not exceed rated cutting capacity of your cutter. See

specifications & capacities for specified cutting capacity.

Exceeding rated cutting capacity can damage drive

components, cutter blades, and deck components.

•

Buildup of debris around moving components and

gearboxes is a fire hazard. Keep rotating parts and

gearboxes free from debris to avoid serious injury and

property damage.

•

Improper oil level can cause bearing failure and be a fire

hazard. Maintain proper gearbox oil level to avoid serious

injury and property damage.

•

Do not operate a broken or bent driveline. Such a driveline

will break apart while rotating at high speeds and can cause

serious injury or death. Always remove the implement from

use until the damaged driveline can be repaired or replaced.

CAUTION

To avoid minor or moderate injury:
Some tractors are equipped with two power take-off speeds.

Do not exceed 1000 rpm power take-off speed or equipment

breakage may result.

Tractor & Cutter Inspection

Make the following inspections with cutter attached to a
tractor, power take-off disengaged, and all moving
components completely stopped:

“Tractor Shutdown Procedure”

on page 16.

2. Inspect tractor safety equipment to make sure it is

installed and in good working condition.

3. Inspect cutter safety equipment to make sure it is

installed and in good working condition.

4. Check driveline to make certain it is securely

connected to the tractor power take-off shaft and
cutter gearbox shaft.

5. Make certain all guards are in good working

condition and in place.

6. Carefully raise and lower implement to ensure

drawbar, tires, and other equipment on the tractor do
not contact cutter frame or driveline.

Check electrical wires to ensure they will not get
pinched or come in contact with rotating drivelines.

8. With cutter resting on solid supports, power take-off

disengaged, and blade rotation completely stopped:

•

Check for and remove foreign objects wrapped
around the blade spindles.

•

Check for nicked, bent, broken, and worn cutting
blades. Replace or sharpen blades as required.
Refer to

“Cutter Blades”

on page 34.

The remaining inspections are made by engaging the
power take-off to check for normal operation.

WARNING

To avoid serious injury or death:
Stop power take-off immediately if vibration continues after a

few revolutions during start-up and anytime thereafter. Wait

for all components to come to a complete stop before

dismounting from tractor to check for probable causes. Make

necessary repairs and adjustments before continuing.

CAUTION

To avoid minor or moderate injury:
Some tractors are equipped with two power take-off speeds.

Do not exceed 1000 rpm power take-off speed or equipment

breakage may result.

9. Start tractor and raise cutter up enough to remove

solid supports from under the deck.

10. Lower cutter down until 2 to 3 inches off the ground.

11. Set throttle to idle or slightly above idle, and slowly

engage power take-off. Initial start-up vibration is
normal and should stop after a few revolutions. Stop
power take-off rotation immediately if vibration
continues.

12. Once cutter is running smoothly, slowly increase

tractor power take-off speed to 1000 rpm. Stop power
take-off rotation immediately if vibration begins to
occur.

13. Investigate cause of vibration and make repairs

before putting the cutter back into service.

Transporting

WARNING

To avoid serious injury or death:

•

When traveling on roadways, travel in such a way that

other vehicles may pass you safely. Use LED lights, clean

reflectors, and a slow moving vehicle sign that is visible

from the back to warn operators in other vehicles of your

presence. Always comply with all federal, state, and local

laws.

•

Reduce ground speed when turning and leave enough

clearance to avoid making contact with obstacles such as

buildings, trees, fences, etc. Making contact can result in

equipment damage and cause serious injury or death.

•

Select a safe ground speed when transporting. Never travel

at a speed which does not allow adequate control of steering

and stopping, and never exceed 20 mph (32.2 km/h) with

attached equipment. Rough terrain requires a slower speed.

•

Select a safe ground speed when transporting. Never travel

at a speed which does not allow adequate control of steering

and stopping, and never exceed 20 mph (32.2 km/h) with

attached equipment. Rough terrain requires a slower speed.

•

Always disengage power take-off and wait for driveline to

stop rotating before raising implement to transport position.

Содержание RCFM4014





















































Результаты поиска

Содержание RCFM4014

Отзывы:

Похожие инструкции для RCFM4014

Бренды по названию

Популярные бренды

Land Pride RCFM4014, Руководство оператора

Результаты поиска

Содержание RCFM4014

Отзывы:

Похожие инструкции для RCFM4014

Бренды по названию

Популярные бренды