Land Pride RCF3684 Скачать руководство пользователя

Страница: 25 / 56

Section 1: Assembly & Set-Up

11/13/18

RCF3684 Rotary Cutters 326-412M

Table of Contents

Hydraulic Hook-up (Pull-Type)

WARNING

To avoid serious injury or death:
Hydraulic fluid under high pressure can penetrate the skin

and/or eyes causing a serious injury. Wear protective gloves

and safety glasses or goggles when working with hydraulic

systems. Use a piece of cardboard or wood rather than hands

when searching for leaks. A doctor familiar with this type of

injury must treat the injury within a few hours or gangrene

may result. DO NOT DELAY.

Refer to Figure 1-19 on page 21:

Make sure spring support loop (#14) is securely
fastened to the hitch frame and fastener hardware is
properly tightened.

2. Route cylinder hose (#9) through spring support loop

(#14) and connect to tractor remote outlet.

3. Check driveline for adequate clearance under all

ranges of cutter height.

a. With driveline attached to tractor and cutter,

slowly raise and lower cutter to its upper and
lower limits while observing clearances between
hitch and driveline.

b. Adjust tractor drawbar height and/or length if

driveline interferes. See Figure 1-18 on page 20
for correct drawbar dimensions.

4. Cycle hydraulic system by extending and retracting

lift cylinder several times. It may be necessary to
purge the hydraulic system of trapped air if operation
is sluggish. Refer to

“Purge Hydraulic System (Pull-

Type)”

on this page.

Purge Hydraulic System (Pull-Type)

DANGER

To avoid serious injury or death:
Be sure deck is lowered to the ground and all hydraulic

pressure is relieved before disconnecting or reconnecting

hydraulic line and/or fittings between Rotary Cutter and

tractor hydraulic system.

With deck skid shoes firmly on the ground, shut
tractor off and move hydraulic control lever back and
forth to relieve all hydraulic pressure in the system.

2. Loosen hydraulic hose fitting at the hydraulic cylinder

slightly to allow air and fluid to escape.

3. Restart tractor and slowly activate tractor control

lever to extend and retract hydraulic cylinder to purge
trapped air from the hydraulic system.

4. Lower cutter down until deck skid shoes are resting

firmly on the ground, shut tractor off, and move
hydraulic control lever back and forth to relieve all
hydraulic pressure in the hydraulic system.

5. After all air is purged from the hydraulic system and

all hydraulic pressure is relieved, tighten hose fitting
at the hydraulic cylinder.

Tractor Hook-up To Pull-Type Cutter

Figure 1-19

33271

Содержание RCF3684

























































Результаты поиска

Содержание RCF3684

Отзывы:

Похожие инструкции для RCF3684

Бренды по названию

Популярные бренды

Land Pride RCF3684, Руководство оператора

Результаты поиска

Содержание RCF3684

Отзывы:

Похожие инструкции для RCF3684

Бренды по названию

Популярные бренды