Land Pride RCF3096, Руководство оператора

Страница: 50 / 76

Section 4: Operating Instructions
Table of Contents
RCF3096, RCF3010, & RCFM3010 Rotary Cutters 326-566M
46
11/8/18
Section 4: Operating Instructions
Operating Checklist
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence and proper
training involved in the operation, transport, maintenance
and storage of the Rotary Cutter. Therefore, it is
absolutely essential that no one operates the cutter
unless they are age 16 or older and have read, fully
understood, and are totally familiar with the Operator’s
Manual. Make sure the operator has paid particular
attention to:
•
Important Safety Information , page 1
•
Section 1: Assembly & Set-Up, page 10
•
Section 3: Adjustments , page 39
•
Section 4: Operating Instructions , page 46
•
Section 5: Maintenance & Lubrication , page 53
Perform the following inspections before using your
Rotary Cutter.
Safety Information
DANGER
!
To avoid serious injury or death:
•
Never place hands or feet under the deck or attempt to make
adjustments to the cutter with power take-off engaged.
Cutter blades rotating at high speeds cannot be seen and are
located close to the deck sides. Body extremities will be cut
off instantly.
•
Do not engage power take-off while hooking-up or
unhooking the driveline, or while someone is standing near
the driveline. A person’s body and/or clothing can become
entangled in the driveline.
Operating Checklist

Check Page
Read and follow all safety information carefully.
Refer to “Important Safety Information”.
1
Make sure all guards and shields are in place.
Refer to “Important Safety Information”.
1
Make sure there are no hydraulic leaks on the
unit. see “Avoid High Pressure Fluids Hazard”.
3
Read and follow preparation instructions. See
"Section 1: Assembly & Set-Up".
10
Read and make all required adjustments.
Refer to "Section 3: Adjustments".
39
Read and follow all operating procedures.
Refer to "Section 4: Operating Instructions".
46
Read and follow all maintenance instructions.
Refer to "Section 5: Maintenance & Lubrication".
53
Read and follow all lubrication instructions.
Refer to "Lubrication Points".
61
Check cutter initially and periodically for loose
bolts and pins. Refer to “Torque Values Chart”.
70
Make sure all gearboxes are properly lubricated.
Refer to Gearbox lubrication.
62
•
Be sure deck is lowered to the ground and all hydraulic
pressure is relieved before disconnecting or reconnecting
hydraulic line and/or fittings between Rotary Cutter and
tractor hydraulic system.
•
All guards and shields must be installed and in good
working condition while operating the implement.
•
Tractor power take-off shaft shield, driveline shields, and
gearbox shaft shields must be installed and in good working
condition to avoid driveline entanglement and projectiles
flying off of the driveline.
•
Rotary Cutters have the ability to discharge objects at high
speeds; therefore, the use of front and rear safety guards is
mandatory when cutting along roadways and in areas where
people may be present. Stop blade rotation if a bystander is
in or around the area.
•
Always disconnect driveline from power take-off shaft
before servicing underside of cutter. The tractor can be
started with power take-off engaged.
•
Do not use cutter as a fan. Cutting blades are not properly
designed or guarded for this use.
•
Do not use a power take-off adapter. The adapter will
increase strain on the tractor’s power take-off shaft causing
possible damage to shaft and driveline. It will also defeat
the purpose of the tractor’s power take-off shield.
WARNING
!
To avoid serious injury or death:
•
Allow only persons to operate this implement who have fully
read and comprehended this manual, who have been properly
trained in the safe operation of this implement, and who are
age 16 or older. Serious injury or death can result from the
inability to read, understand, and follow instructions
provided in this manual.
•
Do not operate and/or travel across inclines where tractor
and/or implement can roll over. Consult your tractor’s
manual for acceptable inclines the tractor is capable of
traveling across.
•
Never carry riders on the implement or tractor. Riders can
obstruct the operator’s view, interfere with control of the
equipment, be pinched by moving components, become
entangled in rotating components, be struck by objects, be
thrown or fall from the equipment, etc.
•
Hydraulic fluid under high pressure can penetrate the skin
and/or eyes causing a serious injury. Wear protective gloves
and safety glasses or goggles when working with hydraulic
systems. Use a piece of cardboard or wood rather than
hands when searching for leaks. A doctor familiar with this
type of injury must treat the injury within a few hours or
gangrene may result. DO NOT DELAY.
•
Perform scheduled maintenance. Check for loose hardware,
missing parts, broken parts, structural cracks, and excessive
wear. Make repairs before putting implement back into
service. Serious breakdowns can result in injury or death.