manualshive.com logo in svg

Land Pride RCF3096, Руководство оператора

Поделиться
Скачать
Land Pride RCF3096 Скачать руководство пользователя страница 32

Section 1: Assembly & Set-Up

Table of Contents

RCF3096, RCF3010, & RCFM3010 Rotary Cutters 326-566M

28

11/8/18

Pull-Type 

Assembly & 

Set-Up

The following pages are 

“Assembly & Set-Up 

Instructions”

 for Pull-Type cutters. Not all instructions 

apply to your cutter. See 

“3-Point Assembly & Set-Up” 

on page 12 and 

“Semi-Mount Assembly & Set-Up” 

on 

page 21.

Tailwheel Lift Options (Pull-Type)

The cutter is shipped with an attached ratchet jack or 
hydraulic cylinder. Hydraulic cylinder option includes 
hydraulic hose, stroke control spacers and quick 
disconnect couplings. The ratchet jack option is lever 
operated at the jack. 

Axle Assembly (Pull-Type)

Refer to Figure 1-21:

There are several hydraulic cylinder/ratchet jack 
mounting lugs (#4) that can be installed on axle (#3). 
Make sure this cutter is equipped with the correct lug and 
that the notch in the lug is located on the axle properly. 
See your nearest Land Pride dealer if mounting lug is not 
installed correctly or is the wrong mounting lug.

NOTE:  

If preferred, rear guards may be assembled 

before the tailwheels. See 

“Assembly of Optional 

Equipment” 

on page 34 for rear guard instructions.

1.

Verify mounting lug is correct as follows:

Models RCF3096 & RCF(M)3010:

 Notch in cylinder 

mounting lug (#4) must be positioned at the back.

Model RCF3096:

 The rod end cylinder pin must be in 

the upper mounting hole in mounting lug (#4).

Model RCF(M)3010:

 The cylinder mounting lug (#4) 

has only one pin hole for the cylinder pin. 

2. Attach left and right-hand tailwheel arms (#1 & #2) to 

axle (#3) with 5/8"-11 U-bolts (#8) and hex flange 
locknuts (#6). Do not tighten locknuts.

3. Adjust tailwheel arms to desired locations. Tighten 

locknuts (#6) to the correct torque.

4. Attach tailwheels (#9) to axle hubs (#5) with 

1/2"-20 x 5/8" high hex nuts (#7). Tighten 1/2" hex nuts 
to the correct torque in a crisscross pattern.

5. If leveling rods (#10) were removed while uncrating 

the unit, reattach them to axle (#3) as shown with 
clevis pins (#11), flat washers (#12), and cotter 
pins (#13). Bend one or more legs of cotter pins to 
secure it in place.

NOTE:  

Pull-Type cutters are supplied with either 

two single tailwheels or four tailwheels arranged in 
dual tailwheel fashion. All tailwheels are shipped 
loose and must be mounted to the axle hubs (#5).

Pull-Type Tailwheel Assembly  (Single  Laminated Tires  Shown)

Figure 1-21

35047

Содержание RCF3096













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды