Land Pride RCF2784 Скачать руководство пользователя | Manualshive

Страница: 5 / 42

background image

3

Important Safety Information

5/08/13

RCF2784 Rotary Cutters 326-364M

Table of Contents

These are common practices that may or may not be applicable to the products described in
this manual.

Prepare for Emergencies

▲

Be prepared if a fire starts.

▲

Keep a first aid kit and fire
extinguisher handy.

▲

Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.

911

Wear
Protective Equipment

▲

Wear protective clothing and
equipment appropriate for the job.
Avoid loose fitting clothing.

▲

Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.

▲

Operating equipment safely
requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.

Avoid High
Pressure Fluids Hazard

▲

Escaping fluid under pressure can
penetrate the skin causing
serious injury.

▲

Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.

▲

Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.

▲

Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.

▲

Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.

▲

DO NOT DELAY. If an accident
occurs, see a doctor immediately.
Any fluid injected into the skin
must be treated within a few
hours or gangrene
may result.

Keep Riders
Off Machinery

▲

Riders obstruct the operator’s
view, they could be struck by
foreign objects or thrown from the
machine.

▲

Never allow children to operate
equipment.

Tire Safety

▲

Tire changing can be dangerous
and should be preformed by
trained personnel using the
correct tools and equipment.

▲

When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.

▲

When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.

Use Seat Belt and ROPS

▲

Operate only tractors equipped
with Roll-Over Protective
Structure (ROPS) and seat belt.

▲

Fasten seat belt snugly and
securely to help protect operator
from being thrown, crushed, or
severely injured if a rollover
occurs; and from falling off the
tractor and being ran over by the
tractor and/or cutter. Not using the
seat belt can result in serious
injury or death.

▲

Wearing protective equipment
such as safety shoes, safety
glasses, hard hat, and ear plugs
is highly recommended.

«
...
3
4
5
6
7
...
»

Содержание RCF2784











































Отзывы:

Нет отзывов

Похожие инструкции для RCF2784

Бренд: RASOR Страницы: 15

Бренд: Ioline Страницы: 5

Бренд: Weidmüller Страницы: 186

Бренд: SIRI Страницы: 16

Бренд: Jonsered Страницы: 32

Бренд: Jonco Страницы: 15

Бренд: Jonsered Страницы: 44

Бренд: Tar River Страницы: 36

Бренд: Raycus Страницы: 27

Ideal Cutter 4810

Бренд: ABC Office Страницы: 8

Бренд: QEP Страницы: 8

Бренд: Accu-Cut Страницы: 37

Бренд: ParkerBrand Страницы: 22

Бренд: Martin Yale Industries Страницы: 4

AUSTROFLIES 320

Бренд: Kaufmann Страницы: 2

Бренд: Textron Страницы: 15

Бренд: Stihl Страницы: 464

Бренд: Stihl Страницы: 332

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды