Land Pride RCF2784 Скачать руководство пользователя

Страница: 38 / 42

Section 6: Features & Benefits

RCF2784 Rotary Cutters 326-364M

5/08/13

Table of Contents

Section 6: Features & Benefits

RCF2784 Model

Features

Benefits

Surpassed rugged
industry standards

All Land Pride Cutters have been designed and tested and meet rigorous voluntary
testing procedures specified by ANSI.

5 Year gearbox warranty

Shows our confidence in the gearbox integrity.

Gearbox Seal Protection

Gearbox bottom seal protection for longer bearing life.

Cat. 4 driveline with
4-plate slip-clutch

Slip-clutch driveline offers convenience for continual work.

Dual position clevis type
3-Point floating top link

Permits deck to follow the terrain for an even cut.

Lower clevis type
3-Point hitch

Allows for ease of hook-up to tractor. Also adds additional strength allowing for an even
pull from the tractor’s lower arms, vs. pulling on a single pin design.

Heavy 10 gauge deck & 1/4" side
skirt construction

Can withstand more abuse than lighter gauge decks.

Box tubing deck supports

Makes for a stronger rigid deck.

Fully welded deck

Adds additional strength.

Extended cutter front

For increased material flow and added protection.

Round back design

Helps discharge grass better than enclosed or partially enclosed cutters.

10 1/8" Deck Height

Allows cutter to handle heavy cutting conditions.

1 1/2" to 12" Cutting height

Provides for a wide range of cutting conditions.

1/4" x 2 1/2" x 18 7/16" Long
skid shoes

Provides sidewall reinforcement and protection to bottom of sidewall.

1/2" x 4" Heat-treated
free swinging blades

Free swinging protects from obstructions. Heat-treated offers longer life.

Splined blade bar hub

Allows for tight positive fit of stump jumper and blade bar to gearbox output shaft.

3/16" x 24" x 38" Oval
stump jumper

Standard Oval stump jumper slides over stumps, rocks and debris.

High blade tip speed

Ensures clean cut.

15" Laminated tailwheel

Laminated material is long lasting in rough conditions. Can’t go flat.

1 1/2" Heavy-duty spindle
on tailwheel

Tailwheels take a beating, spindle gives the strength to protect tailwheel assembly.

Optional Front Guarding

Protect against flying debris.
Customer can choose to include single chain or rubber guarding.

Single Chain Rear Guarding

Protect against flying debris.

Содержание RCF2784











































Результаты поиска

Содержание RCF2784

Отзывы:

Похожие инструкции для RCF2784

Бренды по названию

Популярные бренды

Land Pride RCF2784, Руководство оператора

Результаты поиска

Содержание RCF2784

Отзывы:

Похожие инструкции для RCF2784

Бренды по названию

Популярные бренды