Land Pride RCF2784 Скачать руководство пользователя

Страница: 18 / 42

Section 1: Assembly & Set-up

RCF2784 Rotary Cutters 326-364M

5/08/13

Table of Contents

Trail-Type Axle Assembly

Figure 1-10

33268

Refer to Figure 1-9 on page 15:

11. Move driveline yoke back and forth several times to

make sure yoke is locked in place.

12. Attach safety chain (#1A) to the gearbox cone shield.

Re-latch safety chain to the inner driveline shield.

13. Attach safety chains (#1B & #2A) to the bearing

support assembly (#7). Re-latch safety chain to their
respective driveline shields.

14. Safety chain (#2B) will be attached during tractor

hook-up.

Axle Assembly

Refer to Figure 1-10:

Install tailwheels (#26) to axle frame (#5) with hex
flange lock nuts (#14). Tighten lock nuts to the
correct torque.

Attach axle frame (#5) to rear deck lugs with
3/4"-10 x 2 1/2" GR5 cap screws (#10), spacer
tubes (#1), flat washers (#15), and lock nuts (#11).
Tighten nuts to the correct torque.

Install ratchet jack (#7) or hydraulic cylinder (#8) to
deck assembly as follows:

Ratchet Jack Installation:

a. Attach base of ratchet jack (#7) to mounting lugs

behind gearbox with 1" x 4 3/4" clevis pin (#21) as
shown. Secure clevis pin with hairpin cotter (#19).

NOTE: Tailwheel on right-hand side is not shown to
allow easier viewing of balloons.

b. Operate ratchet lever to extend or shorten ratchet

jack until spring cushioned end of ratchet jack
aligns with hole in axle frame (#5).

c. Insert 1" x 3 3/16" clevis pin (#20) and secure with

hairpin cotter (#19).

Hydraulic Cylinder Installation:

a. Screw vent plug (#9) into port on rod end of

cylinder (#8) until tight.

b. Screw O-ring end of 9/16" straight adapter (#24)

into port of base end of cylinder (#8) until tight.

c. Screw hydraulic hose (#25) to straight adapter

(#24) until tight.

d. Attach quick coupling (coupling supplied by

customer) at tractor end to hydraulic hose (#25)
until tight.

e. Attach base end of hydraulic cylinder (#8)

between and to mounting lugs behind gearbox
with 1" x 4 3/4" clevis pin (#21). Secure clevis pin
with hairpin cotter (#19).

f. Extend hydraulic cylinder until clevis on spring

cushioned end (#6) straddles lug on axle
frame (#5) and holes in clevis aligns with hole in
axle frame lug.

g. Insert 1" x 2 3/4" clevis pin (#16) and secure with

hairpin cotter (#19).

Screw coupler nut (#13) onto long leveling rod (#3)
about 1 3/4".

Содержание RCF2784











































Результаты поиска

Содержание RCF2784

Отзывы:

Похожие инструкции для RCF2784

Бренды по названию

Популярные бренды

Land Pride RCF2784, Руководство оператора

Результаты поиска

Содержание RCF2784

Отзывы:

Похожие инструкции для RCF2784

Бренды по названию

Популярные бренды