Land Pride RCF2784 Скачать руководство пользователя | Manualshive

Страница: 12 / 42

background image

10

Section 1: Assembly & Set-up

RCF2784 Rotary Cutters 326-364M

5/08/13

Table of Contents

3-Point Single Tailwheel Option

Refer to Figure 1-3:

1.

Attach tailwheel A-frame (#1) to inside of rear deck
lugs with 5/8"-11 x 2" GR5 cap screws (#2A), and hex
nylock nuts (#5). Draw nylock nut up snug, do not
tighten.

2.

Install two 2 1/4" OD machine washers (#6A & #6B)
onto tailwheel spindle (#9).

3.

Insert tailwheel spindle (#9) into pivot tube of
A-frame (#1) and install machine washer (#6C)
over tailwheel spindle. Secure tailwheel with
3/8" x 2 1/2" roll pin (#8).

4.

Attach bottom hole of tailwheel adjustment bar (#3)
to deck rear with 5/8"-11 x 2" GR5 cap screw (#2C),
and hex nylock nut (#5). Draw nylock nut up tight, do
not torque tight.

5.

Attach tailwheel adjustment bar (#3) to A-frame (#1)
with 5/8"-11 x 2" GR5 cap screw (#2B), spring lock
washer (#7), and hex nut (#4). Tighten hex nut until
lock washer (#7) is squeezed flat.

Single Tailwheel Assembly

Figure 1-3

33266

«
...
10
11
12
13
14
...
»

Содержание RCF2784











































Отзывы:

Нет отзывов

Похожие инструкции для RCF2784

Бренд: Malco Страницы: 2

Бренд: HOLZMANN MASCHINEN Страницы: 36

Бренд: Vollrath Страницы: 12

Бренд: QEP Страницы: 8

Compact Elite 350-1

Бренд: Logan Страницы: 9

Бренд: Stiga Страницы: 2

Бренд: Stiga Страницы: 2

Бренд: Land Pride Страницы: 3

Бренд: Pace Technologies Страницы: 39

Бренд: iMettos Страницы: 13

Бренд: LESITE Страницы: 8

Бренд: Meister Страницы: 112

Бренд: Daewoo Страницы: 50

Бренд: EINHELL Страницы: 52

Бренд: Land Pride Страницы: 76

Бренд: Partner Страницы: 11

General Purpose Cutter

Бренд: KEENCUT Страницы: 6

Бренд: Dapper Design Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды