Land Pride RCD1884 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 44

background image

Table of Contents

©

Copyright 2020 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

7/13/20

RCD1884 Rotary Cutters 326-355M

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol   . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction: . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . 10

Terminology: . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Definitions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 10

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Further Assistance . . . . . . . . . . . . . . . . . . . . . . . 10

Section 1: Assembly & Set-up . . . . . . . . . . . 11

Tractor Requirements  . . . . . . . . . . . . . . . . . . . . . . 11
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . 11
Uncrating Instructions  . . . . . . . . . . . . . . . . . . . . . . 11
Vented Breather Plug Installation  . . . . . . . . . . . . . 11
3-Point Hitch Assembly  . . . . . . . . . . . . . . . . . . . . . 12
Tractor Hook-Up  . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Quick Hitch Hook-up  . . . . . . . . . . . . . . . . . . . . . . . 12
Driveline Installation  . . . . . . . . . . . . . . . . . . . . . . . 13

Check Driveline Collapsible Length  . . . . . . . . . . 14
Shorten Driveline  . . . . . . . . . . . . . . . . . . . . . . . . 14
Check Driveline Maximum Length  . . . . . . . . . . . 15
Check Driveline Interference  . . . . . . . . . . . . . . . 15

Section 2: Options & Accessories . . . . . . . . 16

Skid Shoe Accessory . . . . . . . . . . . . . . . . . . . . . . 16
Front and Rear Guards . . . . . . . . . . . . . . . . . . . . . 16

Front Corner Deflectors (Standard)  . . . . . . . . . . 16
Front Rubber Guard (Option)  . . . . . . . . . . . . . . . 16
Front Single Chain Guard (Option)   . . . . . . . . . . 16
Rear Metal Band Guard (Standard)  . . . . . . . . . . 18
RCD Rear Extended Metal Guard (Option)   . . . . 18

Section 3: Adjustments . . . . . . . . . . . . . . . . . 20

Deck Leveling & Cutting Height . . . . . . . . . . . . . . . 20
Deck Leveling From Left to Right . . . . . . . . . . . . . 20
Deck Cutting Height . . . . . . . . . . . . . . . . . . . . . . . 20
Tailwheel Height Adjustment . . . . . . . . . . . . . . . . . 21
Center 3-Point Link Adjustment . . . . . . . . . . . . . . . 21

Section 4: Operating Instructions . . . . . . . . . 22

Operating Checklist  . . . . . . . . . . . . . . . . . . . . . . . . 22
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 22
Inspection of Tractor & Cutter  . . . . . . . . . . . . . . . . 23
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Blade Engagement & Disengagement . . . . . . . . . . 24

Blade Engagement . . . . . . . . . . . . . . . . . . . . . . . 24
Blade Disengagement . . . . . . . . . . . . . . . . . . . . 24

Field Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Unhook Rotary Cutter  . . . . . . . . . . . . . . . . . . . . . . 25
General Operating Instructions  . . . . . . . . . . . . . . . 25

Section 5: Maintenance & Lubrication . . . . . 26

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . . 26
Flex Coupler & Blade Timing . . . . . . . . . . . . . . . . . 27
Driveline Protection  . . . . . . . . . . . . . . . . . . . . . . . . 28
Clutch Run-In   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Clutch Assembly and Disassembly  . . . . . . . . . . . . 29
Skid Shoe Maintenance (Accessory) . . . . . . . . . . . 29
Long Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 30
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 30
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Gauge Wheel Spindle Tube  . . . . . . . . . . . . . . . . 31
Gauge Wheel Hub  . . . . . . . . . . . . . . . . . . . . . . . 31
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Flex Coupling Shaft   . . . . . . . . . . . . . . . . . . . . . . 32
Driveline U-Joints  . . . . . . . . . . . . . . . . . . . . . . . . 32
Driveline Shield Bearings  . . . . . . . . . . . . . . . . . . 32
Driveline Profiles   . . . . . . . . . . . . . . . . . . . . . . . . 32
Type of Lubrication: Multi-purpose Grease . . . . . 32

Section 6: Specifications & Capacities  . . . . . 33
Section 7: Features & Benefits   . . . . . . . . . . . 35
Section 8: Troubleshooting  . . . . . . . . . . . . . . 36
Section 9: Torque values Chart  . . . . . . . . . . . 37
Section 10: Warranty   . . . . . . . . . . . . . . . . . . . 39

«
1
2
3
4
5
...
»

Содержание RCD1884













































Отзывы:

Нет отзывов

Похожие инструкции для RCD1884

TASKMASTER TB-CUT120CU-PS

Бренд: Ilsco Страницы: 24

Бренд: IDEAL Страницы: 4

Бренд: Hilti Страницы: 196

Бренд: DeWalt Страницы: 32

XR Li-Ion DCMHT563

Бренд: DeWalt Страницы: 40

Бренд: DeWalt Страницы: 28

Бренд: DeWalt Страницы: 56

Бренд: Makita Страницы: 40

HyDefinition HD4070

Бренд: Hypertherm Страницы: 88

Бренд: Cricut Страницы: 142

Бренд: Land Pride Страницы: 112

Бренд: ATIKA Страницы: 98

Бренд: Agrimate Страницы: 23

Бренд: Stiga Страницы: 38

Бренд: IVT Страницы: 88

Бренд: WAGNER Страницы: 17

Бренд: HSS Hire Страницы: 2

Бренд: Maruyama Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды