Land Pride RCD1884 Скачать руководство пользователя страница 26

Страница: 26 / 44

Section 4: Operating Instructions

Table of Contents

7/13/20

RCD1884 Rotary Cutters 326-355M

Section 4:

Operating Instructions

Operating Checklist

Hazard control and accident prevention are dependent

upon the awareness, concern, prudence, and proper

training involved in the operation, transport, storage, and

maintenance of the Rotary Cutter. Therefore, it is

absolutely essential that no one operates the Rotary

Cutter unless they are age 16 or older and have read,

fully understood, and are totally familiar with the

Operator’s Manual. Make sure the operator has paid

particular attention to:

•

Important Safety Information

, page 1

•

Section 1: Assembly & Set-up,

page 11

•

Section 2: Options & Accessories

, page 16

•

Section 3: Adjustments

, page 20

•

Section 4: Operating Instructions

, page 22

•

Section 5: Maintenance & Lubrication

, page 26

Perform the following inspections before using your

Rotary Cutter.

Safety Information

DANGER

To avoid serious injury or death:

•

Do not engage power take-off while hooking-up or

unhooking the driveline, or while someone is standing near

the driveline. A person’s body and/or clothing can become

entangled in the driveline.

•

All guards and shields must be installed and in good

working condition while operating the implement.

•

Tractor power take-off shaft shield, driveline shields, and

gearbox shaft shields must be installed and in good working

condition to avoid driveline entanglement and projectiles

flying off of the driveline.

•

Never place hands or feet under the deck or attempt to make

adjustments to the cutter with power take-off engaged.

Cutter blades rotating at high speeds cannot be seen and are

located close to the deck sides. Body extremities will be cut

off instantly.

Operating Checklist



Check

Page

Make sure all guards and shields are in place.

Refer to "Important Safety Information".

Follow hook-up & driveline instructions. Refer to

"Tractor Hook-Up" & "Driveline Installation".

12 & 13

Make all required adjustments.

Refer to "Section 3: Adjustments".

Preform all required maintenance. Refer to

"Section 5: Maintenance & Lubrication".

Lubricate cutter and driveline as needed.

Refer to "Lubrication".

Lubricate all gearboxes and replace oil plugs

properly. Refer to "Gearbox" lubrication.

Check cutter initially and periodically for loose

bolts and pins. Refer to “Torque Values Chart”.

•

Always disconnect driveline from power take-off shaft

before servicing underside of cutter. The tractor can be

started with power take-off engaged.

•

Do not use cutter as a fan. Cutting blades are not properly

designed or guarded for this use.

•

Rotary Cutters have the ability to discharge objects at high

speeds; therefore, the use of front & rear safety guards is

mandatory with this cutter. Stop blade rotation if bystanders

are in or around the area. It is recommended that a safety

shield be placed between the operator and cutter on an open

air tractor.

•

Do not use a power take-off adapter. The adapter will

increase strain on the tractor’s power take-off shaft causing

possible damage to shaft and driveline. It will also defeat

the purpose of the tractor’s power take-off shield.

WARNING

To avoid serious injury or death:

•

Select a safe ground speed when transporting. Never travel

at a speed which does not allow adequate control of steering

and stopping, and never exceed 20 mph (32.2 km/h) with

attached equipment. Rough terrain requires a slower speed.

•

Always follow “Tractor Shutdown Procedure” provided in

this manual before dismounting the tractor.

•

Do not operate and/or travel across inclines where tractor

and/or implement can rollover. Consult your tractor’s

manual for acceptable inclines the tractor is capable of

traveling across.

•

Never carry riders on the implement or tractor. Riders can

obstruct the operator’s view, interfere with controls, be

pinched by moving components, become entangled in

rotating components, struck by objects, thrown about, fall

off and be run over, etc.

•

Allow only persons to operate this implement who have

fully read and comprehended this manual, who have been

properly trained in the safe operation of this implement, and

who are age 16 or older. Serious injury or death can result

from the inability to read, understand, and follow

instructions provided in this manual.

•

Perform scheduled maintenance. Check for loose

hardware, missing parts, broken parts, structural cracks,

and excessive wear. Make repairs before putting the

implement back into service.

•

Always disengage power take-off before lifting cutter fully

up. Never operate cutter in the raised position. The cutter

can discharge objects at high speeds.

•

A rotating driveline must not exceed an angle of 25 degrees

up or down, and never engage a driveline while at an angle

exceeding 25 degrees up or down. The driveline can break

and send projectiles.

•

Do not use implement as a man lift, work platform or as a

wagon to carry objects. It is not properly designed or

guarded for this use.

•

Do not exceed rated cutting capacity of your cutter. See

specifications & capacities for specified cutting capacity.

Содержание RCD1884













































Результаты поиска

Содержание RCD1884

Отзывы:

Похожие инструкции для RCD1884

Бренды по названию

Популярные бренды

Land Pride RCD1884, Руководство оператора

Результаты поиска

Содержание RCD1884

Отзывы:

Похожие инструкции для RCD1884

Бренды по названию

Популярные бренды