Land Pride RCD1884 Скачать руководство пользователя страница 20

Страница: 20 / 44

Section 2: Options & Accessories

Table of Contents

7/13/20

RCD1884 Rotary Cutters 326-355M

Section 2: Options & Accessories

Skid Shoe Accessory

Refer to Figure 2-1:

326-341A

RCD1884 SKID SHOES

The RCR1884 cutter is supplied with welded-on skid

shoes. Replaceable skid shoes (Sold as an accessory)

can be bolted to the weld-on skid shoes to increase

protection against side panel wear.

WARNING

To avoid serious injury or death:
Excessive wear on skid shoes can damage side panels, cause

inadequate operation of cutter, and create a safety hazard.

Always replace skid shoes at the first sign of wearing thin.

1. Attach skid shoes (#1) to front left and right corners of

the cutter with 3/8"-16 x 1" GR5 plow bolts (#2), flat

washers (#4), and locknuts (#3).

2. Tighten locknuts to the correct torque.

Skid Shoe Accessory

Figure 2-1

Weld-on Skid Shoe

Replaceable Skid Shoe

33003

Front and Rear Guards

Land Pride strongly recommends front and rear safety

guards be installed on this cutter to help stop objects from

being thrown out from under the cutter at high speeds.

When cutting along highways and in areas where people

or animals may be present, always use front and rear

guards on your cutter.

Front Corner Deflectors (Standard)

Refer to Figure 2- 2 on page 17:

326-490L

FRONT CORNER DEFLECTORS

Front corner deflectors are included with the cutter and

should be installed before installing the front guard.
1. Install corner deflectors (#2) with 3/8"-16 x 1" GR5

carriage bolts (#3) and hex whiz nuts (#6). Draw nuts

up snug, do not tighten.

Front Rubber Guard (Option)

Refer to Figure 2- 2 on page 17:

326-342A

RCR1884 FRONT RUBBER GUARD

1. Install front rubber guards (#1) with 1/2"-13 x 1 1/4"

GR5 carriage bolts (#4) and hex whiz nuts (#5). Draw

nuts up snug, do not tighten.

2. Adjust front guard (#1) and corner deflectors (#2) to

fit evenly against each other.

3. Tighten all whiz nuts (#5 & #6) to the correct torque.

Front Single Chain Guard (Option)

Refer to Figure 2-3 on page 17:

326-449A

FRONT SINGLE CHAIN GUARD

The Single Chain Guard option provides a better flow of

air under the cutter resulting in a more evenly discharge

of cut material.
1. Attach front single chain guard (#1) to deck front with

1/2"-13 x 1 1/4" GR5 carriage bolts (#2) and hex whiz

nuts (#3). Draw nuts up snug, do not tighten.

2. Adjust front chain guard (#1) and corner

deflectors (#2 in Figure 2- 2) to fit evenly against each

other.

3. Tighten all chain guard hex whiz nuts (#3) and corner

deflector hex whiz nuts (#6 in Figure 2- 2)to the

correct torque.

Содержание RCD1884













































Результаты поиска

Содержание RCD1884

Отзывы:

Похожие инструкции для RCD1884

Бренды по названию

Популярные бренды

Land Pride RCD1884, Руководство оператора

Результаты поиска

Содержание RCD1884

Отзывы:

Похожие инструкции для RCD1884

Бренды по названию

Популярные бренды