Land Pride RCD1884 Скачать руководство пользователя страница 35

Страница: 35 / 44

Section 5: Maintenance & Lubrication

Table of Contents

7/13/20

RCD1884 Rotary Cutters 326-355M

Lubrication

Gauge Wheel Spindle Tube

Type of Lubrication: Grease
Quantity = 6 pumps

Gauge Wheel Hub

Type of Lubrication: Multi-purpose Grease
Quantity = 2 pumps

Gearbox

1. Remove side oil level plug (#2) to check oil level. Oil

should be level with bottom of oil level hole.

2. If oil is below bottom of oil level hole, remove vented

breather plug (#1) and add recommended gear lube

through oil fill hole until oil flows out of oil level hole.

3. Reinstall and tighten oil level plug (#2) and vented

breather plug (#1).

4. Repeat steps 1 to 3 above for the other gearbox.
Type of Lubrication: 80-90W EP Gear Lube
Quantity = Fill with oil until oil is level with bottom of oil level

hole. (Oil should just start to flow out the oil level hole.)

NOTE:

Do not overfill! Cutter should be level when

checking oil. Oil expands when hot, therefore, always

check oil level when cold.

30971

30975

Oil Fill Holes

Do Not Overfill

33004

33005

Oil Level Holes

NOTE:

Use a suction or siphon pump to drain

gearboxes of oil when there is not an oil drain plug.

Hours

Hrs

Multi-purpose

spray lube

Multi-purpose

grease lube

Multi-purpose

oil lube

Intervals in hours at which

lubrication is required

Lubrication

Legend

Hours

Содержание RCD1884













































Результаты поиска

Содержание RCD1884

Отзывы:

Похожие инструкции для RCD1884

Бренды по названию

Популярные бренды

Land Pride RCD1884, Руководство оператора

Результаты поиска

Содержание RCD1884

Отзывы:

Похожие инструкции для RCD1884

Бренды по названию

Популярные бренды