Land Pride OFM3678 Скачать руководство пользователя страница 45

Страница: 45 / 68

Section 3: General Operating Instructions

OFM3678, OFM3690 & OFM3698 Offset Flail Mowers 333-149M

6/11/21

Table of Contents

Overturning Hazard

Refer to Figure 3-9:

DANGER

To prevent serious injury or death:

•

Never allow the tractor to take the weight of the flail mower

when working on inclined surfaces (ditches, slopes etc.), as

the combined weight of the tractor and flail mower may

cause the tractor to overturn.

•

Lightweight tractors with rear attached implements may

need weights added to the front to maintain steering control.

Consult your tractor Operator’s Manual to determine

proper weight requirements and maximum weight

limitations.

•

Survey any incline surface the tractor will be traveling on

for holes and low depressions in the ground that the tractor

wheel can drop into suddenly causing the tractor to

overturn unexpectedly. Avoid such drop-offs.

WARNING

To prevent serious injury or death:
Operate only power machines equipped with an enclosed

certified Roll-Over Protective Structure (ROPS) and seat belt.

Fasten seat belt snugly and securely to help protect against

being tossed about and falling.

Working on Incline Surfaces

The flail mower will follow the terrain up or down 65

degrees. When working with the flail on inclining and

declining surfaces, make sure the weight of the flail head

is supported by the roller on the ground and not the

tractor. Setting the incline cylinder to float will assist the

mower in following the terrain.
Plan ahead. Always inspect inclined surfaces for objects

the mower can not pass over and for holes, drop-offs, etc.

the tractor should not go near. Mark any that are not

easily seen with a flag. Make plans on how to avoid

objects, holes, drop-offs, etc. without raising the mower.

Raising the mower can cause an overturning hazard.

Entering a Decline Surface

Slowly move the tractor forward to the edge of the

downward sloped surface while adjusting the incline

angle of the flail head to follow the decline slope. Once

positioned along side the slope to be mowed, engage the

power take-off and begin mowing at a safe travel speed.

Exiting a Decline Surface

Disengage the Power take-off and slowly move the

tractor forward onto level ground while adjusting the

incline angle or the flail head to keep the roller on the

ground. Once on level ground, stop the tractor and adjust

the incline angle as needed.

Tractor Overturn Situation

Figure 3-9

74999

Содержание OFM3678





































































Результаты поиска

Содержание OFM3678

Отзывы:

Похожие инструкции для OFM3678

Бренды по названию

Популярные бренды

Land Pride OFM3678, Руководство пользователя

Результаты поиска

Содержание OFM3678

Отзывы:

Похожие инструкции для OFM3678

Бренды по названию

Популярные бренды