background image

2

TABLE OF CONTENTS

BEFORE GETTING STARTED

Each unit is tested under operating conditions and is thoroughly 

inspected before shipment. At the time of shipment, the 

carrier accepts responsibility for the unit. Upon receiving the 

unit, carefully inspect the carton for visible damage. If 

damage exists, have the carrier note the damage on the freight 

bill and file a claim with carrier. Responsibility for damage to the 

dispenser lies with the carrier.

The installation and relocation, if necessary, of this product must be carried out by qualified personnel with 

up-to-date safety and hygiene knowledge and practical experience, in accordance with current regulations.

IMPORTANT SAFETY INSTRUCTIONS.......................3-4
 

Intended Use..............................................................3

 

Power Warning...........................................................3

 CO

2

 Warning...............................................................3

 

Water Notice...............................................................3

 

Automatic Agitation.....................................................4

SPECIFICATIONS AND FEATURES............................4-5
 

General System Overview..........................................5

PRE-INSTALLATION CHECKLIST...................................5
INSTALLATION............................................................6-12
 

Unpacking the Dispenser............................................6

 

Inspection of Drain Spider...........................................6

 

Selecting/Preparing a Counter Location..................6-7

 

Installing an Icemaker (if necessary)..........................8

 

Dispenser Installation.................................................9

 

Installing Remote Syrup Pumps - Bag In Box..........10

 

Installing CO

Supply.................................................11

 

Dispenser Setup.......................................................12

CLEANING AND SANITIZING..................................13-19
 

General Information..................................................13

 

Cleaning and Sanitizing Solutions............................13

 

Daily Cleaning..........................................................13

 

Ice Bin Cleaning - Start-Up and Monthly..................14

 

Cleaning and Sanitizing Syrup Lines - BIB...............14

 

Cleaning and Sanitizing Nozzle................................15

 

Ice Chute Cleaning...................................................15

 

Removal of Ice Chute for Service.............................15

TROUBLESHOOTING...............................................16-21
 

LED Warnings...........................................................20

 

Automatic Agitation and Low Ice Alarm Control.......21

ILLUSTRATIONS AND PART LISTINGS..................22-25
 

Main Unit Assembly.............................................22-23

 

Wiring Diagram - 115 Volt.........................................24

 

Plumbing Diagram....................................................25

 

Counter Cutout.........................................................25

READ ALL SAFETY INSTRUCTIONS BEFORE USING THIS UNIT.

This manual contains important safety information and all applicable safety precautions must be observed. To reduce 

the risk of fire, electric shock, damage to the equipment or personal injury when using this unit all instuctions/warnings 

on the product being used must be followed:

 

Text following the Warning signal indicates a            

hazardous situation, which if not avoided, will result 

in death or serious injury. Be sure to read all Warning 

statements before proceeding with the installation. 

WARNING

 

Text following the Caution signal indicates a             

hazardous situation, which if not avoided, could result 

in death or serious injury. Be sure to read the Caution 

statements before proceeding with the installation

CAUTION

 

Text following the Attention signal addresses a 

 

situation that if not followed could potentially damage 

the equipment. Be sure to read the Attention 

 

statements before proceeding

ATTENTION

 

Text following the Note signal provides you with 

 

information that may help you more effectively perform 

the installation procedures within this manual. 

 

Disregarding information will not cause damage or 

 

injury, however it may limit the performance of the 

 dispenser. 

NOTE

ABOUT THIS MANUAL

This booklet is an integral and essential part of the product. 

Please carefully read the guidelines and warnings contained 

herein as they are intended to provide the user with essential 

information for the continued safe use and maintenance of the 

product. In addition, it provides 

GUIDANCE ONLY

 to the user 

on the correct services and site location of the unit.

Содержание Sensation





























Отзывы: