PAGE 4
The control valve and fittings are not designed to support
the weight of the system or the plumbing.
Do not use Vaseline, oils, other hydrocarbon lubricants or
spray silicone anywhere. A silicone lubricant may be used
on black o-rings but is not necessary.
Avoid any type of
lubricants, including silicone, on the clear lip seals.
Hydrocarbons such as kerosene, benzene, gasoline,
etc., may damage products that contain o-rings or
plastic components. Exposure to such hydrocarbons
may cause the products to leak. Do not use the
product(s) contained in this document on water
supplies that contain hydrocarbons such as kerosene,
benzene, gasoline, etc.
The optional water meter should not be used as the
primary monitoring device for critical or health effect
applications.
Do not use pipe dope or other sealants on threads. Use
of pipe dope may break down the plastics in the control
valve. Use Teflon tape on the threaded inlet, outlet and
drain fittings.
After completing any valve maintenance involving the
drive assembly or the drive cap assembly and pistons,
unplug power source jack from the printed circuit board
(black wire) and plug back in or press and hold
NEXT
and
REGEN
buttons for 3 seconds. This resets the electronics
and establishes the service piston position. The display
should flash the software version and then reset the valve
to the service position.
Solder joints near the drain must be done prior to
connecting the drain line flow control fitting. Leave at least
6” between the drain line control fitting and solder joints
when soldering pipes that are connected on the drain
line control fitting. Failure to do this could cause interior
damage to the drain line flow control fitting.
Install grounding strap on metal pipes.
This water filter is not to be used for treating water
that is microbiologically unsafe or of unknown
quality without adequate disinfection before or after
treatment.
GENERAL INSTALLATION
AND SERVICE WARNINGS
PRE-INSTALLATION
REVIEW
This water filter is not to be used for treating water
that is microbiologically unsafe or of unknown
quality without adequate disinfection before or after
treatment.
WATER PRESSURE:
Maximum 125 psi. CAUTION:
the filter cannot be subject to a vacuum due to loss of
pressure (such as a water main break or submersible well
pump check valve failure).
WATER TEMPERATURE:
The range of water temperature
is 40°F to 110°F. DO NOT install any water filter with less
than 10 feet of piping between its outlet and the inlet of a
water heater.
AMBIENT TEMPERATURE:
DO NOT locate filter where it
or its connections (including the drain and overflow lines)
will ever be subject to room temperatures under 40°F.
ELECTRICITY:
An uninterrupted 120 volt 60Hz outlet,
within 15 feet of the filter, is required.
Make sure electrical
source is not on a timer or switch.
All electrical connections
must be connected according to local codes. The plug-in
transformer is for dry locations only. Surge protection is
recommended with all electrical connections.
DRAIN:
All plumbing should be done in accordance with
local plumbing codes. The distance between the drain and
the water filter should be as short as possible. Correctly
size drain line for the control valve’s drain line flow control
GPM rating (see installation instructions). Avoid elevating
the drain line above the control valve where possible (see
installation instructions).
BYPASS:
A bypass valve should be installed so that
water will be available if it should be necessary to shut off
the pressure in order to service the filter.
NORMAL OPERATION
BYPASS OPERATION
DIAGNOSTIC MODE
IN
OUT
IN
OUT
IN
OUT
INLET VALVE
OPEN
OUTLET VALVE
OPEN
BYPASS VALVE
CLOSED
INLET VALVE
CLOSED
OUTLET VALVE
CLOSED
BYPASS VALVE
OPEN
INLET VALVE
OPEN
OUTLET VALVE
CLOSED
BYPASS VALVE
OPEN
Click to buy NOW!
PD
F-XCHANGE
w
ww
.docu-track.c
om
Click to buy NOW!
PD
F-XCHANGE
w
ww
.docu-track.c
om
Содержание X FACTOR LX15 Series
Страница 31: ...PAGE 31 NOTES ...
