background image

 

3

REAR PANEL  

As shown in the figure, the following elements ca be seen on the rear panel: 
 

1. Rear handle 
2.  Serial number plate 

 

 

 

3.  DMX address area 

 

 

 

4.  Control Assignment Section 
5.  XLR DMX 512 in/out 

 

6.  Line and electronic fuse 
7.  Main power supply cable 
8.  ON/OFF lamp switch 
9.  RS232 for TRACER console 
10. Projector work hour counter 

 
 

 

ADJUSTMENT OF PROJECTOR BODY ANGLE AND REAR BAR 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

As shown in the figure, in order to be able to control manually the movement of the vertical axis, it’s sufficient to 
loosen the knobs “A”. Thanks to the innovative reinforced bracket with teflon coated disks, you can avoid hard 
adjustments and obtain smooth movement and perfect stability of the product, even in case of “release”. The 
movement, enabled by the support bracket, is +/- 45° compared to the assembly position of the bracket. 
 
In order to recline the rear bar into the desired position it is necessary to loosen the knob “B”. When the new 
positioning has been made, we suggest to tighten firmly the knobs and to verify that the locking is well done before 
operating directly with the projector. 

 
 

 

WORKING POSITION 

SUPERTRACER FOLLOWSPOT 2500 can work in all positions. 

 

 
 

MECHANICAL SAFETY GUARDS 

A bipolar cut-off switch is located between the lamp compartment and the cooling unit. This safety switch cuts off 
the power to the projector if the top lid is opened. 

Содержание Supertracer 2500 HTI


















Отзывы: