background image

 

7

DMX CHANNEL ASSIGNMENT 

 

CHANNEL FUNCTION 

01 COLOUR 

02 COLOUR 

CORRECTION 

03 IRIS 

04 

DIMMER & SHUTTER 

05 FOCUSING 

06 SPECIAL 

FUNCTION 

 
 

DMX CHANNEL FUNCTIONS  are described in the table. 
When you address a projector keep in mind that the BASE CHANNEL (or Starting Channel) corresponds to 
the first channel (the colour channel, in this case), and the other functions follow in the order described in 
the table. 

 
 

When using the projector with a standard DMX controller, the channels with the DIP SWITCHES of control 
assignment channels set on ON can only be used with the TRACER CONSOLE, do not remove the TRACER 
console for any reasons.  
 

 
 

PROJECTOR ADDRESS 

To make sure the projector functions properly , the dip-switches in the DMX ADDRESS AREA on the rear panel 
must be correctly configure. Keep in mind that each SUPERTRACER occupies 6 DMX channels. Each projector 
must be set separately on its own BASE CHANNEL (or STARTING CHANNEL) . The BASE CHANNEL assignment 
is obtained by summing the values for each switch in the DMX SECTION (for example, to set a projector on BASE 
CHANNEL #39, you must set dip-switches 32,4,2 and 1 to the ON position, because 32+4+2+1= 39). In the 
Standard Operating Mode, this means the SUPERTRACER will receive signals on 6 channels following the BASE 
CHANNEL, BASE CHANNEL included (for example, if the projector is set on BASE CHANNEL #39, it will receive 
signals on channels #39, 40, 41, 42, 43 and 44) 

 
 

Содержание Supertracer 2500 HTI


















Отзывы: