manualshive.com logo in svg

Lambrecht rain[e]H3, Руководство пользователя

Поделиться
Скачать
Lambrecht rain[e]H3 Скачать руководство пользователя страница 52

User Manual 

 

Precipitation Sensor rain[e]H3 with Ethernet  

Id-No. 00.15184.540 020

rain[e]H3

 Precipitation Sensor

Manual

14.3.5.  Error Initialisation RTC (Real-Time Clock)

The error is raised if the initialisation of the RTC (Real-Time Clock) fails.

Possible cause:

Troubleshoot:

Connecting cable between 

main board and heating board 

not plugged in

Reconnect the connecting cable of the main board to the heating board. The 

plug snaps into place with a click sound.

Heating board defective!

Replacement heating board

After troubleshooting, please restart the 

rain[e]H3

.

14.3.6.  Error External Temperature Sensor

The error is raised if the external temperature sensor no longer provides data for estimating the type of precipitation.

Possible cause:

Troubleshoot:

Internal heating connector (top) 

not plugged in

Then the error flag “Fault heating“ is also set. Plug the heating connector to 

the heating board.

The outside temperature 

sensor is defective

The outside temperature sensor does not provide any data. The temperature 

sensor must be replaced.

After troubleshooting, please restart the 

rain[e]H3

.

14.3.7  Error Quality of Supply Voltage

The error is raised if the quality of the voltage supply fluctuates strongly.

Possible cause:

Troubleshoot:

External power supply defec-

tive!

Check the external power supply and replace the power supply unit if neces-

sary.

Cable defective (loose contact) Check the supply cable and the connection terminals, or replace the cable if 

necessary. 

After troubleshooting, please restart the 

rain[e]H3

.

15 Repair

Before any repairs on the electronics, it is recommended that the sensor be switched off. The 

rain[e]H3

 has an 

internal switch via which the sensor detects whether the sensor housing is open. When the housing is open or 

not locked, the 

rain[e]H3

 stops the measurement until the housing is closed again.

15.1  Repairs on Site

The following repairs can be carried out on site:
•  Replacing the dirt trap spiral
•  Replacing the protective grid
•  Replacing the collecting vessel
•  Replacing the upper part of the housing, including upper heating and upper temperature sensor
•  Replacing the protective cylinder
•  Replacing the mounting screws (M8x20)
•  Replacing the knurled screw
•  Replacing the level

52

Содержание rain[e]H3




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды