LAMAR CA-1550-CML Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 44

background image

2. INSTALLATION

2

INSTALLATION

2.1

LINE VOLTAGE

The CA-1550-CML can operate on either 115 or 230 volts AC. The desired line
voltage can be changed by opening the unit and modifying the voltage-set jumper(s).
The unit is factory-preset at 115 volts AC.

WARNING: Ensure that the unit is turned off and that no
battery is connected before attempting to open the cover.

CAUTION: Ensure that the unit is set for the appropriate
line voltage before operation.

A.

Turn off the unit and remove any battery

B.

Open the cover by first unscrewing the two screws on the far right of the
front cover.

C.

Locate the four position terminal strip with jumper(s). Note: There is a red
stripe on top of each jumper in the photo below.

D.

Two jumpers are used for 115VAC input and one jumper (across the middle
two screws) is used for 230VAC input. See Figures below.

Jumpers

115 volt AC setting

230 volt AC setting

E.

For 230 VAC operation, the 115 VAC cord must be replaced with one for
230 VAC in required country configuration.

NOTE: If the plug has to be changed make sure to connect
the green AC line wire to ground.

CA-1550 CHARGER / ANALYZER - OPERATING MANUAL LI-4159-CML Rev A

Page 3

«
...
4
5
6
7
8
...
»

Содержание CA-1550-CML













































Отзывы:

Нет отзывов

Похожие инструкции для CA-1550-CML

Бренд: Xantrex Страницы: 4

Бренд: P.I.T. Страницы: 18

Solar Powered Battery Charger

Бренд: GTO Страницы: 4

Бренд: VOLTCRAFT Страницы: 200

Бренд: Sibata Страницы: 4

Бренд: Milwaukee Страницы: 20

Бренд: Raider Страницы: 12

Бренд: Projecta Страницы: 16

Бренд: Gacell Страницы: 25

Бренд: SP tools Страницы: 8

Бренд: Wattsaving Страницы: 16

Бренд: Manson Engineering Industrial Страницы: 15

Бренд: Schumacher Electric Страницы: 56

Бренд: CEMONT Страницы: 56

VELOX 1200T CD.2

Бренд: CEMONT Страницы: 82

Бренд: RadioLink Страницы: 22

Бренд: GreenWorks Pro Страницы: 36

Бренд: Nokia Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды