background image

WB50NBT 

Quick Start Guide 

Embedded Wireless Solutions Support Center: 

 

http://ews-support.lairdtech.com 

www.lairdtech.com/wi-fi

 

 

11 

© Copyright 2016 Laird. All Rights Reserved

 

Americas: +1-800-492-2320 

Europe: +44-1628-858-940 

Hong Kong: +852 2923 0600

 

 

Note:   Consult the CLI documentation for more detailed information regarding the sdc_cli commands and 

other examples for profile configuration. This documentation is available from the Documentation 
tab of the Laird 

WB50NBT product page

. 

3.  The WB should now be connected to the new AP configured in the profile. Type status at the sdc_cli 

prompt and if all is operating correctly you should receive the following output: 

Status: Authenticated 

Config name: quickStart 
SSID: quickStartSSID 
Channel: 36 
RSSI: -71 
Device Name: 
MAC: 00:17:23:e0:38:e4 
IP: (DHCP) 
IPv6:  
AP Name: 
AP MAC: 54:78:1a:e0:42:b0 
Bit Rate: 6 mpbs 
Tx Power: 5 mW 
Beacon Period: 102ms 
DTIM: 1 

Note:  

It is also possible to configure the WB50 NBT using the integrated laird WebLCM via the 
Ethernet or g_ether USB connection. See the Web LCM Linux Platform Application Note for 
information. This documentation is available from the Documentation tab of the Laird 

WB50NBT product page

. 

Bluetooth 

The WB50NBT uses smartBASIC to control the Bluetooth interface. smartBASIC is an event-driven programming 
language designed to make Bluetooth development quicker and simpler. Users can write a smartBASIC 
application to perform Bluetooth operations on the WB50NBT. 

When the WB50NBT powers up, smartBASIC runs as a daemon process which is running a Serial Port Profile to 
Wi-Fi bridging application named SPPBr

In the command line, enter the command ps. The following smartBASIC process appears in the list: 

smartSS -E 7 -d -a -c /usr/share/smartBASIC/apps/$autorun$.SPPBr 

The WB50NBT comes preloaded with sample applications that can be found in the following directory: 
/usr/share/smartBASIC/apps. The SPP-Wi-Fi bridging application in this directory is the same one that the 
WB50NBT automatically runs on boot. This application forms a bridge in between Wi-Fi and Bluetooth SPP and 
sends the data from one interface to another. 

Содержание WB50NBT














Отзывы: