background image

 

Part number 21729, Rev 4 

 

Configuration mode.  The “Relay” column shows whether each alarm is of sufficient priority to 
warrant activating the remote alarm contacts.   

Note that the remote alarm contacts will always have a 30 minute delay to 
activate to allow time for on-site personnel to react to and resolve the alarm 

condition.   

Upon the occurrence of any alarm, the top line of the message center display will list the alarm 
message as shown in the list.  In the case of multiple alarm conditions, the display will show 
each alarm message on the top line in a repeating sequence on three second intervals.  The 
alarms will appear on the message center ONLY when in RUN mode.  If the operator changes to 
a different mode, the alarm LED and the audible alarm will remain active, but the message 
center top line will display whatever the normal message would be in that mode. 

 

Description 

Message 

Audible 

Ring 

Back 

Relay 

High control probe temperature 

HIGH TEMP ALARM 

yes 

yes 

yes 

Low control probe temperature 

LOW TEMP ALARM 

yes 

yes 

yes 

Door is open 

DOOR OPEN  

Yes if 

˃

 1 

min. 

yes 

yes 

Power failure – loss of AC input 

voltage 

POWER FAILURE 1 

yes 

no 

yes 

Power failure – loss of 12V power 

supply 

POWER FAILURE 2 

yes 

no 

yes 

Power failure – output of 12V 

power supply is low with AC 

voltage applied 

POWER FAILURE 3 

yes 

yes 

yes 

Wrong power connected 

WRONG POWER 

yes 

yes 

yes 

High Ambient Temperature 

HIGH AMBIENT TEMP 

no 

n/a 

no 

Low battery voltage 

LOW BATTERY 

yes 

yes 

no 

High stage system failure 

H S SYSTEM FAILURE 

yes 

yes 

yes 

Low stage system failure 

L S SYSTEM FAILURE 

yes 

yes 

yes 

Air flow alarm (determined from 

temp probes) 

AIR FLOW PROBLEM 

yes 

yes 

no 

Low voltage alarm 

LOW LINE VOLTAGE 

yes 

yes 

yes 

High voltage alarm 

HIGH LINE VOLTAGE 

yes 

yes 

yes 

Control Probe failure 

CONT PROBE FAILURE 

yes 

yes 

yes 

Содержание GM-ULT-1786























Отзывы: