Labom CI4 Series Скачать руководство пользователя

Страница: 1 / 36

Level transmitter PASCAL Ci4 LEVEL

Type series CI4xxx

Questions about this device? H49 (0) 4408 804 - 444

LABOM Mess- und Regeltechnik GmbH Im Gewerbepark 13 27798 Hude Deutschland

Tel.: +49 (0) 4408 804-0 Fax: +49 (0) 4408 804-100 e-mail: [email protected] www.labom.com

BA_078

Rev 1F6

Page 1/36

Operating Instructions

General Information....................................................................................................... 2

1.1

General Safety Notes .............................................................................................. 2

1.2

Intended Use ........................................................................................................... 2

1.3

Conformity with EU Regulations .............................................................................. 2

1.4

ATEX Approval ........................................................................................................ 2

Transportation and Storage .......................................................................................... 2

Installation and Commissioning .................................................................................. 2

3.1

Mechanical Installation ............................................................................................ 3

3.2

Electrical Connection .............................................................................................. 3

3.3

Devices with Diaphragm Seal ................................................................................. 4

3.4

Mounting the Remote Display ................................................................................. 4

Operation ........................................................................................................................ 5

4.1

Test Terminals ........................................................................................................ 5

4.2

Remove Display / Activate Write Protection ............................................................ 6

4.3

Maintenance / Service ............................................................................................. 6

Disassembly ................................................................................................................... 7

User Manual ................................................................................................................... 8

6.1

Principles of the parameterisation concept.............................................................. 8

6.2

Basics of the Operating Concept ........................................................................... 11

6.3

Display Mode / Measured Value Display ............................................................... 12

6.4

Menue Mode / Operating Menue ........................................................................... 15

6.5

The Menue Tree .................................................................................................... 18

Содержание CI4 Series





































Результаты поиска

Содержание CI4 Series

Отзывы:

Похожие инструкции для CI4 Series

Бренды по названию

Популярные бренды

Labom CI4 Series, Руководство по эксплуатации

Результаты поиска

Содержание CI4 Series

Отзывы:

Похожие инструкции для CI4 Series

Бренды по названию

Популярные бренды