![background image](http://html2.mh-extra.com/html/labom/ci4-series/ci4-series_operating-instructions-manual_3191650036.webp)
BA_078 Rev 1F6 Level transmitter PASCAL Ci4 LEVEL
Page 36/36
6.5.11 Overview with menue tree and device functions
…
Setting other output values
Status
Display status of level measurement
Units
Select units for measurands and parameters
Height…
Select unit for fill height and height offset
Pressure…
Setting a fixed pressure value
Tank shape
Parameterising the tank shape
…
Submenus (view/edit, teach, units, etc.)
Height…
Setting a fixed height value
Simulation
Current…
Setting a fixed current value
Height offset
Parameterising the height offset
…
Submenus (view/edit, teach, unit)
…
Submenus (view/edit, teach, unit)
Config.-memory
Configuration memory: reading, writing and status
Config.-memory
Configuration memory: reading, writing and status
Device reset…
Restarting the device (such as after a power outage)
System
Device ID…
Setting the device ID (e.g. to display a free-text in the display)
Device data…
Display of device data (same as from measured value display)
HART data…
Display of HART information (HART tag, HART descriptor, etc.)
Send-preambles…
Setting of the number of send preambles for HART communication
Factory reset…
Reset to factory settings
…
Various screens with device data
Communication
HART address…
Setting the HART address for device identification in multi-drop mode
Current mode…
Setting the current mode (proportional/constant)
Display and reset min/max-Values for the different output values
Maintenance timer
Management of maintenance intervals
Status…
Displaying and stopping the maintenance timer
Set interval…
Setting and starting the maintenance timer
Limit of the upper output current (20…21 mA)
Last error…
Display and reset of the last critical error
Self test…
Self test of the device like after applying the power supply
Diagnosis
Counters…
Display of operating hour counter and maintenance timer
Min/max-values
View and edit value for 4 mA
teach…
Teach value for 4 mA
…
Display and reset the different Min/Max-values
Alarm Current…
Selection of the alarm current: High (>21 mA) or low (<3.6 mA)
Lower Current Limit…
Limit of the lower output current (3.8…4.0 mA)
Upper Current Limit…
Measurement/Output
Value at 20 mA
Value of selected measurand that shall correspond to 4 mA
Measuring Rate…
Setting of the measuring rate (20 or 100 Hz)
Output value
Select measurand that shall be shown at the current output
view / edit…
1st value…
Content for 1st value in the selected layout
…
Content for further values (up to five)
Damping…
Setting the damping of the output signal
Decimal Point…
Selection of the decimal places by specifying the decimal point
Backlight…
Switch backlight on/off
Screen Layout…
Define screen structure and layout
Display
Language…
Select menu language
…
More units
4 mA…
Adjust 4mA
20 mA…
Adjust 20 mA
Display Mode
Configuration of the display layout and content
Lower Adjustment…
Offset correction with applied reference pressure
Upper Adjustment…
Span correction with applied reference pressure
Current Adjustment
Adjustment of the current output
Zero Point…
Set device at ambient pressure to zero (0 bar rel) (only for gauge pressure devices)
Position Correction
Correct zero point error due to installation position (only for gauge pressure devices)
…
Set, activate and deactivate position correction
Adjustment
Pressure Adjustment
Adjustment of the pressure measurement
Level
Level wizard…
Guided parameterisation of the level measurement
Density
Parameterising the density
Quick Setup
Language…
Select menu language
Level wizard…
Guided parameterisation of the level measurement
view / edit…
View and edit value for 20 mA
teach…
Teach value for 20 mA
Damping…
Setting the damping of the output signal
Value at 4 mA
Value of selected measurand that shall correspond to 4 mA
Device ID…
Setting the device ID