56
1 - GENERAL INFORMATION
The EN/RF1 single-channel receiver is a 433.92 MHz radio receiver designed to open the ETERNA 90 automatic door using transmitters
manufactured by Label. Table 1 lists the radio transmitters manufactured by LABEL S.p.A.
2 - USE
The EN/RF1 receiver must be coupled to the J8 connector of the ET-LOGIC-B electronic control unit and it is prearranged to control the
opening of the automatic door in all the automation work programs.
The automatic door opening control is given by radio-control, while the protection and safety of the door movement are ensured by devices
outside the receiver itself.
It shall never be used in any case where the door activation or deactivation may cause injuries and damage.
Class 3 receiver in compliance with the ETSI EN 300-220-1 V.2.1.1 (2006-04) standards, chapter 4.1.1.
3 - INSTALLATION OF THE RECEIVER
Couple the EN/RF1 receiver (fig. 1) to the J8 connector of the electronic control unit
ET-LOGIC-B (fig.2).
Proceed with saving of radio-controls (fig.3) as follows:
a) Enter the programming mode of transmitters pressing and holding the SW1 button until the L1 led is steadily lit (approx. 3 seconds).
b) Press the button of the transmitter to be saved and the successful saving will be indicated by 5 fast flashings of the L1 led.
c) Afterwards, the L1 led will be steadily lit again and it will be possible to save another transmitter by repeating the described operation from
step b) and so on with all the transmitters to be used.
A maximum of 250 transmitters can be saved on the receiver.
d) Once the transmitter saving procedure is finished, exit the programming mode by pressing and holding the SW1 button until the L1 led
turns off (
o
).
4 - USE OF THE RADIO-CONTROL
By pressing the button of a saved transmitter, the automatic door opens and the L1 led of the receiver will remain on until the button of the
transmitter is released.
The radio-control opens the door in all the automation work programs.
5 - CANCELLATION OF THE MEMORY OF THE RECEIVER
Should it be necessary to cancel all the saved transmitter codes from the memory of the EN/RF1 receiver, proceed as follows:
a) Extract the EN/RF1 receiver from the connector of the ET-LOGIC-B control unit.
b) Keep the receiver SW1 button pressed and then couple again the EN/RF1 receiver to the J9 connector of the ET-LOGIC-B control unit.
c) Release the EN/RF1 receiver SW1 button only when the L1 led of the receiver starts blinking.
At this stage the L1 led of EN/RF1 blinks fast to indicate that the receiver is ready to save the codes of all LABEL transmitters, both
rolling code and dip switch.
If you only wish to save the rolling code transmitters (SPYCO model), excluding all dip switch models, briefly push the SW1 button; the L1
led will blink slowly to indicate that the receiver is ready to only save the SPYCO transmitter codes.
To switch between the modes briefly push the SW1 button once.
d) After selecting the desired mode, hold the SW1 button pressed for about 3 seconds until the L1 led begins blinking very fast for about
8 seconds, signalling the receiver memory is being erased.
e) When the cancellation of the memory of the EN/RF1 receiver is finished, the L1 led will turn off.
f) At this point, it is possible to save again the code of the transmitters to be used, following the procedure described in paragraph 3.
6 - TECHNICAL SPECIFICATIONS
Power supply
12Vdc
Absorption
10mA stand-by - 50mA in operation
Outputs
OPEN COLLECTOR
Frequency
433.92 Mhz
Memory capacity
250 users
Range without obstacles
30 meters
Operating temperature
-20° / +55°
Receiver class (ETSI EN 300-220-1 Chapter 4.1.1)
Class 3
7 - DECLARATIONS
Marketing, sale and use are valid without restrictions in all EU countries.
With this document Label SpA declares that the EN-RF1 receiver complies with all the essential requirements and with all other relevant
dispositions established by 1999/5/EC directive.
The declaration of conformity is annexed to the EN/RF1 receiver instructions.
2
8
) EN/RF1 RADIO RECEIVER
