Labconco SteamScrubber 45780 Series Скачать руководство пользователя | Manualshive

Страница: 24 / 70

background image

Chapter 3: Getting Started

Product Service 1-800-522-7658

20

20

To set up the washer control:

1.

Locate the control panel on the front of the washer.

2.

Press and hold the

▼

button and close the handle of the washer by sliding the door

latch knob to the right. Hold for 5 seconds.

3.

The display will show the SET UP screen.

4.

The > on the left side will highlight VOLTAGE.

5.

Press the

◄

or

►

buttons to select the correct operating voltage of the washer.

CAUTION: The voltage selected (115V or 230V) does not change the acceptable
AC mains voltage that can be connected to the washer. It only selects the
programs that are suitable for the identified voltage.

6.

Press the

▼

button and TEMP UNITS will highlight.

7.

Press

◄

or

►

buttons to select either °F or °C which will be used on the display to

set and monitor temperature.

8.

Press the

▼

button and DI PUMP ENABLE will highlight.

9.

Press

◄

or

►

buttons to YES or NO. This allows the pure water valve and pump

to be disabled if pure water will not be used for rinse cycles and prevents
inadvertently programming a cycle to have pure rinses.

10.

Press the

▼

button and LIGHT will be highlighted on the display.

11.

Press

◄

or

►

to cause the light inside the tank on window models to be turned on

or off while the door is latched.

12.

Press the

▼

button and LIQ DETERGENT OPT will be highlighted on the display.

13.

Press

◄

or

►

to activate the control for the liquid detergent dispense option if this

accessory has been installed.

14.

Press the

▼

button and FACTORY RESET will be highlighted on the display.

15.

Press the

◄

or

►

to select YES to erase all program set points entered by the user

and to restore all set points that were active when the washer was shipped.

16.

Press RUN to save all settings.

Testing Your Washer

Now that you have made the required water and electrical connections to your
washer, a series of diagnostic steps are provided in this section to test the
operation of the washer.

Before turning on the washer, make certain the water is turned on and no packing
material remains inside the washer.

«
...
22
23
24
25
26
...
»

Содержание SteamScrubber 45780 Series







































































Отзывы:

Нет отзывов

Похожие инструкции для SteamScrubber 45780 Series

Бренд: Haier Страницы: 20

Бренд: Landa Страницы: 24

Бренд: CDA Страницы: 44

Бренд: Kärcher Страницы: 268

Бренд: ZANKER Страницы: 40

XPERT-HD 3.8/35 P

Бренд: Landa Страницы: 16

Бренд: Spitwater Страницы: 21

Бренд: Pacific hydrostar Страницы: 17

Бренд: P&C Страницы: 45

Бренд: Magic Chef Страницы: 32

CLOTHES-PROCESSOR EZ 3600 CEE

Бренд: Equator Страницы: 16

Бренд: Eswood Страницы: 17

Бренд: Hotpoint Страницы: 76

Бренд: Hotpoint Страницы: 2

Бренд: Alfa Network Страницы: 20

Бренд: Kärcher Страницы: 172

Бренд: Daewoo Страницы: 7

Бренд: Mach Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды