L-Card L-502-P-G-D-I Скачать руководство пользователя

Страница: 72 / 73

Bibliography.

[1]

L-502. Programmer guide. - M.: L-Card, 2013

[2]

Low-level programmer manual for the L-502 board. - M .: L-Card, 2013

[3]

A. V. Garmanov. - "Connection of measuring devices. Electrical compatibility and noise immunity".

- M.: L-Card, 2003

[4]

Terminology for measuring systems – technical support section on the L-Card website:

www.lcard.ru/lexicon

[5]

Error! Hyperlink reference not valid.

List of tables.

Table 4-1: Eternal signal connector ....................................................................................................... 34

Table 4-2: Internal signal connector ...................................................................................................... 37

Table 4-3: Intermodule synchronization connector .............................................................................. 39

Table 4-4 The maximum permissible modes are described for the L-502 module installed in the

computer's system unit ................................................................................................................... 42

Table 4-5Maximum permissible through current by GND, AGND, DGND ...................................... 42

List of figures

Fig. 1-1. Symbol system for L-502 module ............................................................................................ 7

Fig.1-2. L-502 version 3 (face layout) .................................................................................................. 11

Fig. 1-3. L-502 version 1 or 2 (face layout) ......................................................................................... 12

Fig.1-4. L-502 (back layout) ................................................................................................................. 13

Fig. 3-1. Illustration of the personnel principle for acquiring ADC data ............................................ 23

Fig. 3-2. L-502 synchronization system structure................................................................................. 25

Fig. 3-3. The principle of obtaining ADC data (in detail) ................................................................... 27

Fig.3-4. Synchronous I/O diagram........................................................................................................ 29

Fig. 3-5. Block diagram .......................................................................................................................... 31

Fig. 4-1: Eternal signal connector .......................................................................................................... 34

Fig. 4-2: Internal signal connector ......................................................................................................... 36

Fig. 4-3: Example of a grouped connection of digital lines: three buses of 8 bits each. .................... 38

Fig. 4-4: Intermodule synchronization connector (L-502 version 1 and 2). ....................................... 38

Fig. 4-5: Intermodule synchronization connector (L-502 version 3)................................................... 39

Fig. 4-6: Multi-module synchronization scheme .................................................................................. 40

Содержание L-502-P-G-D-I










































































Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Похожие инструкции для L-502-P-G-D-I

Бренды по названию

Популярные бренды

L-Card L-502-P-G-D-I, Руководство пользователя

Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Похожие инструкции для L-502-P-G-D-I

Бренды по названию

Популярные бренды