L-Card L-502-P-G-D-I страница 40 Скачать руководство пользователя

Страница: 40 / 73

Connection of signals.

CON

OUT

START

_OUT

CON

DGN

START

_IN

DGN

L-502 #3

CON

OUT

START

_OUT

CON

DGN

START

_IN

DGN

L-502 #2

CON

OUT

START

_OUT

CON

DGN

START

_IN

DGN

L-502 #1

(

ведущий

)

(

ведомый

)

(

ведомый

)

Fig. 4-6: Multi-module synchronization scheme

Fig. 4-7: The scheme of multi-module synchronization of three L-502 version 3 (top view of the

computer's motherboard)

The synchronization cable for a pair of L-502 modules, which, if necessary, must be ordered

separately, is designed to connect two L-502 modules. For connecting N pcs. of L-502 modules on one
motherboard you will need (N-1) pcs. of synchronization cables.

If, at least, one L-502 in this connection scheme does not have galvanic isolation, then the entire

system of these modules loses the galvanic isolation of the signal circuits from the ground and the
computer case.

The four-wire synchronization cable L-502-SYNC connects one pair of L-502 modules. The

pinout of the cable is made according to the "one-to-one" scheme. For orientation during

installation, use the key

on the casing of the cable connector. At the same time, on each side of

the cable, when installed according to the scheme

fig. 4-7

, the key must be oriented in the same

direction.

Ведущий

Ведомый

Slave #2

Master

Slave #1

(master)

(slave)

Содержание L-502-P-G-D-I










































































Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Похожие инструкции для L-502-P-G-D-I

Бренды по названию

Популярные бренды

L-Card L-502-P-G-D-I, Руководство пользователя

Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Похожие инструкции для L-502-P-G-D-I

Бренды по названию

Популярные бренды