![background image](http://html1.mh-extra.com/html/l-b-white/cr035/cr035_owners-manual-and-instructions_3146488008.webp)
1.
Read all safety precautions and follow L.B. White
recommendations when installing this heater. If
during the installation or relocating of heater, you
suspect that a part is damaged or defective, call a
qualified service agency for repair or replacement.
2.
Position heater properly before use. The heater must
be installed on a level, flat, horizontal, and stable
surface when hot or in operation and according to
minimum clearances from combustible surfaces such
as walls, or ceilings. Do not place combustible
materials within this zone of clearance. Minimum
safe distances are as follows:
Top to Ceiling
3.3 ft (1.0 m)
Sides and back
3.3 ft. (1.0 m)
Front
4.5 ft. (1.37 m)
Gas Supply
6 ft. min. (1.83 m)
3.
L.P Gas Installation Requirements
■
Ensure all L.P. gas containers are secured from
accidental tip over and are protected from people,
vehicular traffic, and contact.
-- Use a stabilizer for smaller 20/30/40 pound (9
14,18 KG) LP gas containers to keep them upright
during use and transport. See Fig. 1.
■
L.P. gas containers must be located on a flat,level,
and stable surface.
FIG. 1
Contact your local authorities, L.P. gas dealers, or fire
marshalls for specifics dealing with installation in
your area.
4.
Position the heater and its gas supply hose so as to
protect heater and its gas supply hose from traffic.
Protect hoses with a shielding device of suitable
nature to protect the hose from traffic and movement
or other construction equipment.
5.
The heater is approved for indoor use only. The
heater shall be installed so it is not directly exposed
to water spray, rain, and /or dripping water.
6.
The heater’s gas pressure regulator (with pressure
relief valve) must be protected from adverse weather
conditions (rain, ice, snow) as well as from building
materials (tar, concrete, plaster, etc.) which can affect
safe operation and could result in property damage or
injury.
7.
Heaters used in the vicinity of combustible tarpaulins,
canvas, plastics, wind barriers, or similar coverings
shall be located at least 10 feet (3.05 m) from the
coverings. The coverings shall be securely fastened
to prevent ignition or upsetting of the heater due to
wind action on the covering or other material.
8.
Check all connections for gas leaks using approved
gas leak detectors. Gas leak testing is performed as
follows:
-- Check all pipe connections, hose connections,
fittings and adapters upstream of the gas
control with approved gas leak detectors.
-- In the event a gas leak is detected, check the
components involved for cleanliness and
proper application of pipe compound before
further tightening.
-- Furthermore tighten the gas connections as
necessary to stop the leak.
-- After all connections are checked and any
leaks are stopped, turn on the main burner.
-- Stand clear while the main burner ignites to
prevent injury caused from hidden leaks that
could cause flashback.
WARNING
Fire or explosion hazard.
Can cause property damage, severe injury or death.
1. To avoid dangerous accumulation of fuel gas, turn off
the gas supply at the heater service valve before
starting installation, and perform gas leak test after
completion of installation.
2. Do not force the safety gas control button. Use only
normal hand pressure to depress the button. Never
use any tools. If the button will not operate by
normal hand pressure, the control should be
replaced by a qualified service technician. Force or
attempted repair may result in fire or explosion.
7
Installation Instructions
GENERAL
WARNING
Fire and Explosion Hazard
■
Do not use open flame (matches, torches, candles,
etc.) in checking for gas leaks.
■
Use only approved leak detectors.
■
Failure to follow this warning can lead to fires or
explosions.
■
Fires or explosions can lead to property damage,
personal injury or loss of life.
LP GAS CONTAINER
SECURED WITHIN
STABILIZER
Содержание CR035
Страница 2: ......
Страница 18: ...17 Parts Identification Parts Schematic...
Страница 38: ...Identification des pi ces composantes SCHEMA DES PIECES COMPOSANTES 18...