L-Acoustics K Series Скачать руководство пользователя

Страница: 73 / 120

Rigging procedures

Adding a pullback with K3-RIGBAR

Type of deployment

own array

Rigging accessory

K3-RIGBAR
2 × Ø19 mm shackles WLL 3.25 t (provided)

Min number of operators

Pickup points must be aligned with the linking points.

under K3-RIGBAR

under K3-BAR

Procedure

Optionally, secure another K3-RIGBAR on the top enclosure to replace K3-BUMP as the main lifting accessory.

Prepare an array of K3. Refer to

Flying an array with K3-BUMP and K3-BAR

(p.67).

Raise the array.

Secure the LA-SLING2T to the second motor hook.

Make sure the chains are not twisted.

Attach K3-RIGBAR to the sling using the two 3.25 t WLL shackles.
Use the interior holes of the bar.

The external holes are dedicated to additional safety.

K3 owner's manual (EN) version 1.0

Содержание K Series

























































































































Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды

L-Acoustics K Series, Руководство пользователя

Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды