L-Acoustics K Series Скачать руководство пользователя

Страница: 59 / 120

Inspection and preventive maintenance

Listening test

enclosure

preset

usable bandwidth

[K3 70]

42 Hz - 20 kHz

Kara II

[KARA II 70]

55 Hz - 20 kHz

KS28

[KS28_100]

25 Hz - 110 Hz

KS21

[KS21_100]

31 Hz - 100 Hz

Procedure

Load the preset on an LA4X / LA8 / LA12X amplied controller.

Connect a sinus generator to the amplied controller.

Risk of hearing damage

Set a low sound level to start and use ear protection to adjust before testing.

Scan the bandwidth focusing on the usable range.

The sound should remain pure and free of unwanted noise.

Troubleshooting for LF speakers

One or more LF speaker produces distorted, buzzing, rubbing, clicking, mufed or weak sound.

Possible causes

• The screws are not tightened with the appropriate torque.
• There is an air leak in the gasket.
• There is dust on the cone.
• The cone is damaged.
• The surround is torn or delaminated.
• The voice coil or the spider is damaged.

Procedure

Perform the speaker disassembly procedure.

Visually inspect the cables and the connectors.

Visually inspect the speaker cone, the voice coil and the spider.
If any damage is visible, replace the speaker.

Carefully clean the speaker with a dry cloth.

Perform the reassembly procedure.
Replace the speaker gasket and the screws.
Apply the recommended torque.

Repeat the listening test.
If the problem persists, replace the speaker.

K3 owner's manual (EN) version 1.0

Содержание K Series

























































































































Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды

L-Acoustics K Series, Руководство пользователя

Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды