L-Acoustics K Series Скачать руководство пользователя

Страница: 21 / 120

Rigging system description

Rigging system description

On both sides, K3 integrates two arms to connect another element of the rigging system, such as an enclosure or a ying

frame.

• At the front, a rotating arm provides a xed point around which the enclosure can freely rotate until its connection at

the rear.

• At the rear, a sliding arm enables the inter-element angle setting and the inter-element rear connection.

The angles between adjacent enclosures are secured by an automatic system that is activated in advance and locks itself

during the stacking and lifting procedures.
Eight angle positions are available: 0.25°, 1°, 2°, 3°, 4°, 5°, 7.5°, 10°.

Two ergonomic handles on both sides of the enclosure are available for transportation.

K3 owner's manual (EN) version 1.0

Содержание K Series

























































































































Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды

L-Acoustics K Series, Руководство пользователя

Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды