L-3 Technologies CyTerra Range R2D Link Скачать руководство пользователя страница 34

Страница: 34 / 102

Approved for Public Release 20 October

2015 by U.S. Army Project Manager I2WD

10/13/2017

Approved for Public Release 20 October

2015 by U.S. Army Project Manager I2WD

CyTerra

Brightness Adjustment

•

The brightness level of the display is adjustable via a menu selection.

•

To increase the brightness, select up and press the top scan button.

•

To decrease the brightness, select down and press the top scan button.

•

Orientation of the system does not affect the button use.

Zoom Feature and Adjustment

•

The Zoom feature can only be accessed while in the Scan Mode. The top

and bottom scan buttons also control this function.

•

The scan buttons allow the operator to zoom in or zoom out.

•

Warning: The unit must settle for approximately 3-5 seconds after

scanning has started for the Zoom feature to work.

INSTRUCTION POINTS

Содержание Range R2D Link







































































































Результаты поиска

Содержание Range R2D Link

Отзывы:

Похожие инструкции для Range R2D Link

Бренды по названию

Популярные бренды

L-3 Technologies CyTerra Range R2D Link, Руководство по эксплуатации и обучению

Результаты поиска

Содержание Range R2D Link

Отзывы:

Похожие инструкции для Range R2D Link

Бренды по названию

Популярные бренды