L-3 Technologies CyTerra Range R2D Link Скачать руководство пользователя страница 65

Страница: 65 / 102

Approved for Public Release 20 October

2015 by U.S. Army Project Manager I2WD

10/13/2017

Approved for Public Release 20 October

2015 by U.S. Army Project Manager I2WD

CyTerra

Operators Effect on the System:

The operator should remain as still as possible. This is especially important
when the sensor is being used in standoff from a wall. The system will display
no new information while the Operator Movement Indicator is displayed.

Operator
Movement
Indicator

OPERATOR INDUCED ERRORS

If the Operator Movement Indicator
appears, first attempt to stabilize
the system.

If the indicator persists, attempt to
rescan.

Содержание Range R2D Link







































































































Результаты поиска

Содержание Range R2D Link

Отзывы:

Похожие инструкции для Range R2D Link

Бренды по названию

Популярные бренды

L-3 Technologies CyTerra Range R2D Link, Руководство по эксплуатации и обучению

Результаты поиска

Содержание Range R2D Link

Отзывы:

Похожие инструкции для Range R2D Link

Бренды по названию

Популярные бренды