KYMCO Yager 200i Скачать руководство пользователя

Страница: 58 / 76

Brake fluid

Your scooter is equipped with a hydraulic brakes. Check the

brake fluid level window

on the master cylinder reservoirs

on the handlebars per the maintenance schedule.

1. Remove the two Phillips screws retaining the master cylin-

der cap. Remove the cap.

2. Add the specified type of brake fluid to bring the level above

the “L” level in the window.

3. Wipe the master cylinder cap and gasket with a clean cloth

and reinstall the cap, tightening the screws securely.

Adding brake fluid:

Brake fluid type:

DOT 4

Do not mix brake fluid types, as it may cause brake failure

and could result in an accident. Do not allow brake fluid

to touch the body work, as it will damage its surface.

MAINTENANCE

Brake pad inspection

Brake pad wear on your scooter depends upon the severity of

usage, the type of riding, and road conditions (generally, the

pads will wear faster on wet and dirty roads). Inspect the pads

at each regular maintenance interval.

Front right/left brake pads

Check the cutout in each brake pad, the cutout should be vis-

ible, indicating that brake pad is not worn down to the brake

rotor. If either pad is worn to the cutout, replace both pads as

a set.

NOTE: See your KYMCO dealer for brake pad service.

Содержание Yager 200i













































































Результаты поиска

Содержание Yager 200i

Отзывы:

Похожие инструкции для Yager 200i

Бренды по названию

Популярные бренды

KYMCO Yager 200i, Руководство пользователя

Результаты поиска

Содержание Yager 200i

Отзывы:

Похожие инструкции для Yager 200i

Бренды по названию

Популярные бренды