KYMCO Yager 200i Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 76

KYMCO Yager 200i Скачать руководство пользователя страница 17

15

Multifunction display - Digital clock

CONTROLS & FEATURES

The clock indicates the time in hours and minutes when the

ignition is “ON”. The clock display also indicates AM or PM.

To adjust the clock’s time manually, follow this procedure:

1. Tune the ignition switch “ON”
2. Press and hold the ADJUST button for more than two sec-

onds to select the ODO mode

NOTE: The digital clock can be only be adjusted in the
ODO mode. Do not select the tripmeter or oil service meter
mode if you want to adjust the time on the clock.

3. Press and hold both the MODE button and the ADJUST

button at the same time for more than two seconds. T he

“hour” digits will begin flashing, indicating the clock time can

be adjusted

4. To set the hour display , press the ADJUST button until it

displays the correct “hour” time

5. To change the minute display, press the MODE button until

the “minute” digits begin flashing

6. To set the minute display , press the ADJUST button until it

displays the correct “minute” time

«
...
15
16
17
18
19
...
»

Содержание Yager 200i













































































Отзывы:

Нет отзывов