KYMCO Yager 200i Скачать руководство пользователя

Страница: 46 / 76

NOTE: Change the engine oil with the engine at normal

operating temperature with the scooter positioned on its

main stand to assure complete and rapid draining.

1. Remove the oil filler/dipstick

from the right crankcase

cover.

2. Place a suitable container (drain pan) under the left crank-

case.

The engine and related components can become very

hot. Use care when inspecting or adjusting the oil level

to avoid injury. If needed, let the engine and exhaust

system cool before working in those areas.
Prolonged contact with used engine oil can cause skin

cancer. Although rare, this possibility exists if you

handle oil on a frequent basis. Thoroughly wash your

hands with soap and water as soon as possible after

handling used oil.

Do not overfill the engine with oil. Overfilling the en-

gine can cause oil leaks and/or oil contamination of

the air filter element. Always make sure the oil level is

above the "L" mark but not higher than the "F" mark.

MAINTENANCE

Engine oil replacement

Engine oil quality is the primary factor affecting engine lon-

gevity. Change your scooter's engine oil as specified in the

maintenance schedule (see pages 39 - 41).
NOTE: When riding your scooter in very dusty conditions,

oil changes should be performed more frequently than

specified in the maintenance schedule.

NOTE: Always dispose of used engine oil in a environ-

mentally responsible manner. Take the drained oil in a

sealed container to your local recycling center or service

station for reclamation. Do not throw the oil in the trash,

pour it on the ground, or pour it down a drain.

Содержание Yager 200i













































































Результаты поиска

Содержание Yager 200i

Отзывы:

Похожие инструкции для Yager 200i

Бренды по названию

Популярные бренды

KYMCO Yager 200i, Руководство пользователя

Результаты поиска

Содержание Yager 200i

Отзывы:

Похожие инструкции для Yager 200i

Бренды по названию

Популярные бренды