KYMCO 2006 MXU 500 Off-Road Скачать руководство пользователя страница 340

Страница: 340 / 677

7. ENGINE REMOVAL/INSTALLATION

7-9

MXU 500

Install the compression spring into the

pinion gear.

Move the engine rearward and engage the

rear propeller shaft into the pinion gear.

Install the upper engine mounting bolt and

nut loosely.

Install the rear lower engine mounting bolt

and nut loosely.

Install the engine hangers and four engine

hanger nuts loosely.

Install the front lower engine mounting bolt

and nut loosely.

Tighten the four engine hanger nuts to the

specified torque.

Torque:

3.5 kgf-m (35 N-m, 25 lbf-ft)

Tighten the all engine mounting bolts and

nuts to the specified torque.

Torque:

6 kgf-m (60 N-m, 43.5 lbf-ft)

Apply grease Pinion Gear

Compression Spring

Apply lightweight lithium-soap base

grease to the pinion gear splines.

＊

Install the joint boot securely.

＊

Lower Engine Mounting Bolt/Nut

Engine Hanger Nuts Engine Hanger

Содержание 2006 MXU 500 Off-Road






































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 2006 MXU 500 Off-Road

Отзывы:

Похожие инструкции для 2006 MXU 500 Off-Road

Бренды по названию

Популярные бренды

KYMCO 2006 MXU 500 Off-Road, Руководство пользователя

Результаты поиска

Содержание 2006 MXU 500 Off-Road

Отзывы:

Похожие инструкции для 2006 MXU 500 Off-Road

Бренды по названию

Популярные бренды