KYMCO 2006 MXU 500 Off-Road Скачать руководство пользователя страница 332

Страница: 332 / 677

7. ENGINE REMOVAL/INSTALLATION

7-1

MXU 500

SERVICE INFORMATION

GENERAL INSTRUCTIONS

A floor jack or other adjustable support is required to support and maneuver the engine.

Be careful not to damage the machine body, cables and wires during engine removal.

Use shop towels to protect the machine body during engine removal.

The following components require engine removal for serviced with the engine installed in the

frame.

Oil pump (Chapter 4)

Water pump (Chapter 6)

Cylinder head (Chapter 8)

Cylinder/Piston (Chapter 9)

Drive and driven pulleys/clutch (Chapter 10)

Alternator/Starter clutch (Chapter 17 and 19)

The following components require engine removal for service.

Transmission (Chapter 11)

Crankshaft/Crankcase/Balance shaft (Chapter 12)

TORQUE VALUES

Engine mounting bolt/nut

6 kgf-m (60 N-m, 43.5 lbf-ft)

Engine hanger nut

3.5 kgf-m (35 N-m, 25 lbf-ft)

Front propeller shaft bolt

4.5 kgf-m (45 N-m, 32.5 lbf-ft)

Содержание 2006 MXU 500 Off-Road






































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 2006 MXU 500 Off-Road

Отзывы:

Бренды по названию

Популярные бренды

KYMCO 2006 MXU 500 Off-Road, Руководство пользователя

Результаты поиска

Содержание 2006 MXU 500 Off-Road

Отзывы:

Бренды по названию

Популярные бренды