KYMCO 2006 MXU 500 Off-Road Скачать руководство пользователя страница 329

Страница: 329 / 677

. COOLING SYSTEM

6-17

MXU 500

WATER TEMPERATURE
SENSOR

Remove the right side body cover and right

footboard (refer to the “

FRAME

COVERS

” section in the chapter 2).

Disconnect the water temperature sensor

connector.
Remove the water temperature sensor from

the water joint.

INSPECTION

Connect the water temperature sensor to the

ohmmeter and dip it in oil contained in a

pan which is placed on an electric heater.
Gradually raise oil temperature while

reading the thermometer in the pan and the

ohmmeter connected. If the resistance

measured is out of specification, replace the

temperature gauge with a new one.

Temperature

Standard resistance

50ºC

123.9

–

478.9

100ºC

–

29.3

After the water temperature sensor has been

installed, fill coolant and perform air

bleeding (refer to the “

COOLANT

REPLACEMENT

” section in this

chapter).

INSTALLATION

With thread lock applied to the threaded

part, tighten the water temperature sensor.

Torque:

0.8 kgf-m (8 N-m, 5.8 lbf-ft)

Water joint

Water Temperature Sensor

Thermometer

Water Temperature Sensor

Handle the water temperature sensor

carefully as it is vulnerable to impact.

Do not allow the water temperature

sensor and the thermometer to come in

contact with the bottom of the pan.

＊

Содержание 2006 MXU 500 Off-Road






































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 2006 MXU 500 Off-Road

Отзывы:

Похожие инструкции для 2006 MXU 500 Off-Road

Бренды по названию

Популярные бренды

KYMCO 2006 MXU 500 Off-Road, Руководство пользователя

Результаты поиска

Содержание 2006 MXU 500 Off-Road

Отзывы:

Похожие инструкции для 2006 MXU 500 Off-Road

Бренды по названию

Популярные бренды